Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Repair in North Las Vegas: What to Know First
We repair FAAC swing and sliding gate operators across North Las Vegas, and most jobs are done in a single visit. Common repairs run $180 to $480, and you’ll get an exact written price before we turn a wrench. In most cases we can get eyes on your gate within a few business days, and emergencies get handled the same day when we can make it happen. We’re an independent FAAC service provider – not tied to the factory, not affiliated with the manufacturer – which is exactly why we can fix the operator instead of selling you a new one.
This page is for the homeowner with a FAAC 400, 770, or 390 already mounted on a column, hearing a grind, a stall, or a gate that quits halfway. Call us at (844) 761-9351 and a live person picks up.
How FAAC Products Fail – and How We Fix Them
FAAC builds sturdy operators. What breaks on them in North Las Vegas is specific, and it’s usually not the brand’s fault – it’s heat, dust, and a part that wore out. Here’s what we open up and find.
- FAAC 400 swing operators – the limit switch drift. The 400 series is the most common residential FAAC we see in North Las Vegas. When the gate starts stopping early or reversing on its own, it’s usually the encoder or the limit cams drifting, not a dead motor. The fix is a reset and a mechanical cam adjustment, then a full cycle test – not a new operator.
- FAAC 770 and 390 sliding operators – worn pinion gear and chain slack. Sliders on a long North Las Vegas driveway run hard, especially in summer heat. We see the drive pinion wear flat and the chain stretch, which throws the gate off its rack. We re-tension, replace the pinion, and true the rack so the gate rides level.
- Control board and photobeam failures after a windstorm. Desert wind drives grit into the FAAC control box, and we find the safety photobeams misaligned or the board faulting. We clean, re-aim the beams, and test the reverse-on-obstruction before we leave.
- Hinge, post, and weld failures on the gate leaf itself. A FAAC operator is only as good as the gate it’s pushing. A sagging leaf strains the motor. We weld on site – a gate sags in the hinge post, not the middle, and that’s where we start.
- Battery and backup faults. On FAAC units with battery backup, a dead cell shows up as the gate stalling under a power blip. We test the battery under load and swap it rather than guess.
Show me the gate closing on its own and I’ll show you where it’s failing. That’s how we diagnose a FAAC job – the operator tells you what’s wrong if you know how to read it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our FAAC Gate Repair Process
A real FAAC job, start to finish, looks like this:
- 1
You call, a live person answers. We ask what the gate is doing and which FAAC unit you have – the model is on a plate inside the housing.
- 2
We come out and diagnose on site. We open the operator, check the control board for fault codes, test the motor and limit switches, and look at the gate leaf, hinges, and posts.
- 3
Parts decision. We use OEM FAAC parts when the job calls for it and quality aftermarket where it makes sense and stays warranty-safe. You hear the difference in price and why before we order.
- 4
The repair. We weld on site when the leaf needs it, so the gate stays in your driveway. No hauling it off, no swapping parts that don’t need swapping.
- 5
The test. We cycle the gate open and closed, test the safety reverse, and check the operator for heat or noise.
- 6
The guarantee and the cleanup. Every job carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings us back.
See the difference
Before
After
Before
After
Before
AfterWhat FAAC Gate Repair Costs in North Las Vegas
Prices depend on which FAAC unit you have and what failed. Here are honest ranges for what we handle in North Las Vegas:
| FAAC repair | Typical range |
|---|---|
| Control board or limit-switch reset and adjustment | $180 – $340 |
| Photobeam realignment or safety sensor replacement | $160 – $290 |
| Pinion gear / chain re-tension on a slider | $220 – $420 |
| Hinge, post, or weld repair on the gate leaf | $250 – $480 |
| Battery backup replacement (load-tested) | $150 – $270 |
What moves the price: gate size, whether the leaf needs welding, and whether the part is OEM FAAC or an aftermarket match. What doesn’t move it is the quote at the door. Our pricing is upfront and agreed before any work starts – no surprises on the invoice. Estimates are free, and you get $40 off any repair over $200, no trip charge inside the county, and 10% off for seniors and veterans.
Why North Las Vegas Homeowners Call Gatewood Fence & Gate North Las Vegas for FAAC Work
We’re locally owned and owner-operated, and the name is on the shop down the road. That accountability matters when your FAAC 770 is stuck open and you need a real person, not a call queue. We answer 24/7, and our technicians have up to 25 years of experience. We’re certified across nine major gate brands – FAAC, plus LiftMaster, Mighty Mule, Ghost Controls, and DoorKing among them – so if your gate is a mix of systems, we can still sort it out. Every job carries the 90-Day Done Right Promise in writing, and our pricing is no-hassle upfront. If you’ve been burned by an outfit that quoted one number on the phone and another at the door, you’ll find we do the opposite.
FAQs
Will repairing my FAAC gate void the factory warranty? Not if the repair is done correctly with the right parts. We use OEM FAAC parts where the warranty requires it, and we tell you up front when an aftermarket part is the smarter choice. Call (844) 761-9351 and we’ll talk through your options.
Can you get FAAC parts for my North Las Vegas gate? Yes, for most current FAAC lines including the 400, 770, and 390 series. If a part is back-ordered, we’ll tell you the real timeline rather than guess. Estimates are free.
Should I repair or replace my FAAC operator? Repair is almost always cheaper and our first move. We replace only when the motor or board is truly dead and past saving. Bring us any written estimate for a free second opinion.
How fast can you get to a FAAC gate that’s stuck open? Where we can, we get to it the same day. For non-emergencies, we’ll give you a real appointment window, not a four-hour guess. Call (844) 761-9351.
Do you weld on site? Yes. We weld on site so the gate stays in your driveway instead of being hauled off. That saves you a day without your gate and often a tow charge.
Call (844) 761-9351 for a free estimate on your FAAC gate repair in North Las Vegas. A live person answers, we show up in the window we promise, and the price is agreed before any work starts.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.