Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Parts & Welding in North Las Vegas: What to Know First
We provide independent FAAC gate parts and welding in North Las Vegas, usually getting a swing or sliding gate back on its track in one visit once the right part is on hand. Most mechanical repairs – hinges, posts, rails, rollers, latches, custom welding – finish same day. Operator boards and control parts can take a few days to source. You get a written price before we touch anything, and it doesn’t change when the work is done. This page is for FAAC owners in North Las Vegas who want a straight answer on what’s wrong and what it costs. Call (844) 761-9351 and a live person picks up, day or night.
How FAAC Products Fail – and How We Fix Them
FAAC builds serious equipment, and when it fails it usually fails in a predictable spot. Here’s what we actually find on FAAC gates around North Las Vegas, and what we do about it.
- 950-series swing arm mounts loosen and the arm walks off the bracket. The 950 and its siblings are heavy 24V swing operators with a lot of torque for their size. Over a few summers the anchor bolts and mounting plate work loose in the concrete, the arm opens at an angle, and the gate starts dragging on the driveway before it ever hits the stop. We re-set the plate, weld reinforcement if the bracket is fatigued, and re-align the arm to the factory geometry instead of cranking the limits to hide it.
- Sagging swing gates that the operator gets blamed for. A FAAC operator pushing a gate that has dropped two inches at the latch looks like an operator fault. It almost never is. The sag lives in the hinge post, not the middle of the gate, and a post that’s heaved in caliche soil will keep pulling the gate out of square no matter how many times the operator is re-learned. We replace the post and re-hang the hinges before touching the motor.
- Corroded hinge barrels and stitch-welded hinge plates on older installs. Plenty of North Las Vegas gates were put up by builders who tack-welded the hinge to the frame in two spots instead of running a proper bead. Those joints crack and rust from the inside. We cut the old hinge off, clean back to bare steel, and weld a full replacement hinge plate so it holds.
- Roller and track wear on FAAC sliding operators. The 844 and similar sliding units run on ground tracks and guide rollers that wear flat and start to bind. A binding gate overloads the operator and eventually trips the board. New rollers and a straightened or replaced track section usually solve it, and the operator stops working so hard.
- Latch, lock, and post-mount hardware rusted solid. Coastal-desert dust and the occasional monsoon soak will seize a latch or lock cylinder faster than people expect. We free and re-key where it’s sound, and replace where the hardware is past saving, matching the gate’s swing and the operator’s soft-stop so nothing slams.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our FAAC Gate Parts & Welding Process
Here’s how a FAAC job runs from the first call to the last weld bead cooling on your driveway.
- 1
Diagnose on site. We look at the whole gate, not just the part that broke – post, hinges, frame, track, and operator – because a FAAC motor working against a bent gate will fail again next month.
- 2
Decide OEM versus aftermarket. For FAAC control boards and specific operator components, OEM is often the only path that keeps the unit reliable. For hinges, rollers, latches, and structural steel, a quality aftermarket part is frequently stronger and cheaper. We tell you which is which and why.
- 3
Quote it in writing. You get the price before any work starts. If something changes once we open it up, we stop and talk to you first.
- 4
Repair and weld on site. The gate stays in your driveway. We weld the hinge, post, or rail repair right there and re-hang and re-align as we go.
- 5
Test under real load. We cycle the gate repeatedly, check the limits, force settings, and soft-stop, and confirm nothing binds.
- 6
Clean up and back it in writing. We leave the site clean and hand you the 90-Day Done Right Promise stamped on the job.
See the difference
Before
After
Before
After
Before
AfterWhat FAAC Gate Parts & Welding Costs in North Las Vegas
Every FAAC job is different, but here are the ranges we typically quote for the work you’re most likely to need. These are honest ballparks, not phone-quote bait. The exact figure is set on site and agreed before we start.
| Job | Typical range |
|---|---|
| Hinge replacement (per hinge, welded) | $150 – $350 |
| Hinge or gate post replacement | $350 – $900 |
| Rail or frame repair, on-site welding | $200 – $600 |
| Gate roller replacement (set) | $120 – $300 |
| Latch and lock service or replacement | $100 – $275 |
| Custom welding / fabrication | Quoted per job |
| FAAC operator board or control part | Parts plus labor, quoted per unit |
What moves the price: whether the repair is bolt-on or weld-in, how much rust and old repair we have to cut out first, and whether a part is a stocked item or a special order. We give free estimates and a free second opinion on any written estimate you’ve already got. Standing offers that need no haggling: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (844) 761-9351 for an exact quote.
Why North Las Vegas Homeowners Call Gatewood Fence & Gate North Las Vegas for FAAC Work
We’re an independent FAAC service provider, not affiliated with or authorized by FAAC – and that’s exactly why we can fix the part that failed instead of replacing the whole operator. As an owner-operated shop, we’ve been repairing what other companies want to replace since 2001, with our address published and our name on every invoice. Our technicians have up to 25 years of experience, background-checked and on every job.
Every job carries our 90-Day Done Right Promise in writing – if it’s not done right, one call brings us back, no runaround. A live person answers the phone 24/7, so you’re never stuck listening to a voicemail. We’re certified to service nine major gate brands, so if your FAAC gate shares hardware or a control setup with a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing system nearby, we speak that language too. One gate, one problem, one person who shows up when they said they would.
FAQs
Yes, we source FAAC parts, including operator boards and control components, as an independent service provider. Common mechanical parts like hinges, rollers, latches, and steel repairs are quick, while specific FAAC electronic components may take a few days to order. Call (844) 761-9351 and we’ll tell you what’s in stock and what needs ordering.
Mechanical repairs like welding a hinge or replacing a roller don’t touch the operator’s warranty. We’re careful on the electrical side and never do anything that could compromise a unit still under FAAC coverage. If your operator is under warranty, tell us up front and we’ll work around it.
Most of the time, repair. A sagging gate or a cracked hinge is a structural fix, not an operator replacement, and welding the failed part usually costs a fraction of a new gate. We’ll tell you honestly when a gate is genuinely past saving and why.
Mechanical repairs – hinges, posts, rails, welding, latches – are often done same day once we’re on site and the part is available. We give you a real window and keep it. Call (844) 761-9351 to get on the schedule.
No, there’s no trip charge inside the county. We give a free estimate and a free second opinion on any written estimate you’ve already received, so you can compare before you commit. Upfront pricing, agreed before work starts.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.