Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Motor Replacement: The North Las Vegas Owner’s Guide
FAAC gate motor replacement in North Las Vegas typically runs $850 to $1,900 installed, depending on which FAAC series you own and whether the operator arm or the control board is the failed component. In many cases we can source the right replacement motor and have your gate swinging again the same day. Most owners find out the motor is dying the same way: the gate starts reversing halfway through a cycle, or it hums without moving, and the last thing they want is a sales pitch for a whole new system when one part has quit.
Which FAAC Models This Applies To
We service the FAAC swing and slide operators common on residential driveways around North Las Vegas: the 390, 391, 400, 402, 422, 452, and the 740/741 slide series. FAAC sells these in different voltage and control-board configurations, so the model number on the data plate inside the housing matters more than the brand name on the arm. Before we quote anything, we read that plate and check the motor’s capacitor rating, the arm’s stroke length, and the control board revision, because two FAAC motors that look identical from the driveway can take completely different replacement parts.
On the OEM-versus-aftermarket question, we give it to you straight. A genuine FAAC motor matches the original spec exactly, which matters on older 400-series units where a clone with a different torque curve will run hot and short its life. A quality aftermarket equivalent is reasonable on the simpler 390/391 swing arms, and it can save you several hundred dollars. We’ll tell you which one your specific operator is a good candidate for, and we won’t push the pricier option when the cheaper one is honestly fine. Gatewood Fence & Gate North Las Vegas is an independent service company and isn’t affiliated with FAAC.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Gate Motor Replacement Is Failing
FAAC operators fail in predictable ways. Here’s what we see when we pull into a driveway in North Las Vegas:
- Gate reverses mid-cycle or stops short. Usually a failing limit switch or a control board that’s losing its position memory. The motor is fine; the brain that tells it where to stop isn’t. On a FAAC this often traces back to a wet board after a monsoon-season downpour.
- Motor hums or whines but the gate doesn’t move. The capacitor has given out, or the gearbox inside the arm is stripped. A hum with no travel almost always means the motor is trying to turn and the drive train won’t let it.
- Arm is stiff, grinding, or leaking oil. The gearbox seals have failed. Desert dust and 110-degree summer heat chew up the lubricant inside these units faster than in milder climates, and a grinding FAAC arm is telling you the gears are on their way out.
- Gate works only from the keypad, not the remote (or vice versa). A failed receiver module, not the motor. Worth diagnosing before anyone quotes you a full replacement, because it’s often a far cheaper fix.
- Motor runs but the gate drifts or won’t hold position. On swing operators this can be a worn clutch or a bad encoder, and it will eventually stall the motor. A gate that won’t hold closed is a security problem, not a door that sticks.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s an honest range for the North Las Vegas market. Swing-arm operator replacement for a standard residential FAAC typically lands between $850 and $1,400 installed. Slide-gate operators run $1,100 to $1,900 installed, because the track, chain, and rack-and-pinion setup adds labor. Control-board-only jobs, when the motor is still good, usually come in under $450 and we’ll tell you when that’s all you need.
The quote is agreed and written before we touch a thing, and it doesn’t change at the door. What drives the range: which series you own, whether the existing wiring and power run are sound, and whether we’re doing a straight swap or adapting an older mounting bracket. Every replacement is backed by our 90-Day Done Right Promise, stamped in writing on the job. Standing offers apply too: $40 off any repair over $200, no trip charge inside the county, and 10% off permanently for seniors and veterans. You’ll get a free second opinion on any written estimate you’re holding.
DIY or Call Us?
You can safely check a few things yourself: confirm the breaker to the operator is on, look for water in the control box, test whether the keypad works when the remote doesn’t, and clear any debris from the track or the swing arc. That’s the safe list.
What you should not do is open the operator housing and start swapping the motor, capacitor, or control board on your own. These run on 120-volt line power, the capacitor holds a charge even after the breaker’s off, and the swing arm carries stored tension that can slam shut or snap back without warning. A gate motor install also involves getting the limit switches and force settings right so the gate reverses when it meets an obstruction. Get that wrong and you’ve built a gate that won’t stop for a child or a dog. A trained professional handles that. Call us at (844) 761-9351 and we’ll take a look, same day when we can.
FAQs
A well-installed FAAC motor typically lasts 10 to 15 years in North Las Vegas, though the desert cuts that short for some units. The 110-degree summer heat breaks down internal lubricant and the monsoon-season rain that sneaks into control boxes corrodes boards. A unit mounted in full afternoon sun with no shade cover tends to fail years earlier than one that catches some shade.
Often, yes. A bad capacitor, a failed control board, or a stripped receiver doesn’t mean the whole motor is shot, and we’ll repair those before we quote a full replacement. We’ll open it up, diagnose the actual failed component, and tell you honestly whether a repair makes financial sense or whether the motor’s wear means you’d be throwing money at a part on its way out anyway.
A straight FAAC swing-arm swap usually takes two to four hours once we have the right part on site. Slide operators and jobs where wiring or brackets need adapting can run longer, occasionally into a second visit. When you call, we’ll tell you the realistic window, and we hold to it.
We read the model and revision off your operator’s data plate, then match the motor, control board, and arm stroke to your exact unit. FAAC has changed specs across board revisions over the years, and we check those before ordering rather than assuming two similar-looking motors are interchangeable. We service LiftMaster, Mighty Mule, and Ghost Controls too, and we’re certified to handle FAAC alongside the other eight major gate brands.
If your FAAC gate is reversing, humming, or stuck, don’t wait for it to fail completely. A live person answers our line 24 hours a day, seven days a week, no voicemail and no call center. Hal’s name is on the shop and every invoice, and that’s the oldest accountability there is. Call (844) 761-9351 for a free estimate, upfront pricing, and the 90-Day Done Right Promise in writing.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.