Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Hinge & Roller Replacement: The North Las Vegas Owner’s Guide
We replace FAAC hinges and rollers with compatible parts for $180 to $420 installed, depending on the model and how much of the carriage has worn out, and we can often get to it the same day here in North Las Vegas. The parts are matched to your arm and operator, the work is tested under power before we leave, and the price is quoted and agreed before anyone touches a bolt.
Most owners don’t discover a hinge or roller problem sitting still. They hear it first – a grind at the top of the swing, a slap when the gate closes, a roller that squeals two houses away. Then they notice the gate no longer sits level in the middle of travel, or the operator has started reversing on its own. That’s usually a worn hinge pin or a roller that has flat-spotted and stopped rolling true. In North Las Vegas, the fine dust that settles on everything reaches the carriage track faster than most people expect.
Key Takeaways
- Installed FAAC hinge and roller replacement in North Las Vegas runs $180 to $420.
- Price is quoted and agreed before work starts – no surprise at the door.
- Compatible parts are matched to your model, not to a generic sliding-gate kit.
- Every job carries the 90-Day Done Right Promise in writing.
- A permanent 10% discount for seniors and veterans, plus $40 off any repair over $200.
Which FAAC Models This Applies To
FAAC swing operators show up on lots all over North Las Vegas, and the hinge and roller hardware is specific to the arm style and the gate weight it was built to move. Residential swing lines – the 390, 391, 400, and S418 families – use a different roller carriage and hinge pin length than the heavier 740 and 750 series. The 400 series and its variants are the most common on neighborhood driveways; the heavier 740/750 arms usually live on estate gates or commercial entries. Getting the part right starts with the operator, not the gate.
To identify yours, look for the data plate on the underside or side of the operator housing. It carries the model and, often, the build code. If the plate is gone or unreadable, we measure instead: hinge pin diameter to the millimeter, carriage track width, and the gate leaf weight the arm is rated for. Those numbers tell us which FAAC hinge and roller set the gate was actually built around.
On the OEM-versus-aftermarket question, we’re straight with people. For a well-used gate, a quality compatible hinge and roller set performs as well as the original for a fraction of the price, and we’ll tell you when that’s the honest call. Where OEM matters – heavy leaves, tight tolerances, or a model where the original pin geometry is unusual – we say so and we source it. We claim no stock: we don’t carry parts on a truck or in a warehouse, so the right part is ordered and matched to your model. We’re also an independent service provider, not affiliated with FAAC; we’re certified to service nine major brands, and FAAC work is a big part of what we do in North Las Vegas.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Hinge & Roller Replacement Is Failing
A hinge or roller that’s going bad usually shows it before it quits. Watch for these:
- Grinding or squealing during the swing. The roller or the hinge pin has lost its lubricant film and is running metal on metal. By the time it’s loud, the pin is usually scored and no amount of spray fixes it for long.
- The gate sags in the hinge post. A gate sags in the hinge post, not in the middle – and that’s where we start. A worn hinge allows the leaf to drop at the pivot, which throws off the whole alignment.
- The operator reverses or strains mid-swing. A flat-spotted or seized roller binds the carriage, the arm meets resistance, and the operator’s safety circuit reads it as an obstruction. Owners often blame the motor when it’s the roller.
- A rattle or slap when the gate closes. A roller with a worn bore knocks in the track at the end of travel. Left alone, that slap hammers the carriage and speed up wear on the arm.
- Visible flat spots, cracks, or a wobbling hinge pin. Pull the gate open by hand and watch the roller as it rides the track. Any hitch, flat spot, or side-to-side wobble in the pin means the part is done.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed FAAC hinge and roller replacement in North Las Vegas runs $180 to $420. Here’s what moves the number:
| What’s involved | Typical installed range |
|---|---|
| Single roller set, standard residential arm (390/391/400 series) | $180 – $260 |
| Full hinge and roller set, both leaves | $260 – $360 |
| Heavy series (740/750) or OEM-specific pin geometry | $340 – $420 |
| Track or carriage repair found during the job | Quoted separately, agreed before work |
What drives the range: the model, how many hinges and rollers are actually worn versus just tired, and whether the carriage track needs attention while we’re in there. We quote parts and labor together and itemize them, and that price is agreed before we start. A free second opinion on any written estimate is standing offer, and the work carries the 90-Day Done Right Promise in writing – if it’s not done right, we make it right.
DIY or Call Us?
Some of this you can safely check yourself. Pull the gate open by hand with the operator disengaged and watch the rollers ride the track. Flat spots, wobble, or a hinge pin you can wiggle by hand are all things you can spot in five minutes. That’s the looking part, and we’d rather you do it than guess.
The swap is where it gets harder. A heavy FAAC leaf under spring or arm tension can pinch or crush a hand if it shifts, and a hinge pin driven out of a loaded gate is not a one-person job. Matching the replacement part to your model also matters more than people expect – the wrong pin length or roller width will grind a track flat in a month. This is a part where a wrong guess costs more than the repair. If you’d rather not mess with it, call us at (844) 761-9351 and we’ll take a look. A live person answers, any hour.
FAQs
Expect five to eight years on a residential gate, shorter on heavy leaves or gates opened dozens of times a day. The dust and dry heat in North Las Vegas dry out the pin lubricant faster than a coastal climate would, and a gate with a tired hinge tends to wear its rollers out early too.
Sometimes – a seized roller can often be cleaned, re-lubricated, and put back in service if the bore and pin are still true. Once a pin is scored or a roller has a flat spot, replacement is the honest call. We’ll tell you which one you’re looking at. Call (844) 761-9351 for a free second opinion on any written estimate.
A standard residential roller set is usually a one-to-two-hour job; a full hinge and roller set on both leaves runs two to four hours. We test the gate under power before we leave and show you it closing clean. Same-day is often possible in North Las Vegas.
We start with the data plate on the operator, and if it’s gone we measure the pin, carriage, and track to match the part to what the gate was built around. We order the compatible or OEM part to your model rather than guessing from a generic kit. Call (844) 761-9351 and we’ll sort out which part you need.
If your FAAC gate is grinding, slapping, or fighting the operator, don’t wait for it to quit on a Sunday. Call us at (844) 761-9351 for a free estimate – a live person answers, and we’ll quote the hinge and roller replacement upfront before any work starts. We’re certified to service FAAC along with LiftMaster, Mighty Mule, and Ghost Controls, and we’re happy to look at whatever you’ve got.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.