Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Welding & Fabrication: The North Las Vegas Owner’s Guide
We fix broken FAAC gate hardware the right way: welding and fabricating the damaged pivot, bracket, arm mount, or hinge point right on the gate in your driveway, usually the same day you call. Most North Las Vegas welding and fabrication repairs on FAAC systems run $180 to $420 installed, depending on how much structural metal has to be cut out and rebuilt. The price gets quoted and agreed before we strike an arc. You’ll find us in North Las Vegas regularly because steel gates here take a beating: 110-degree summer afternoons, dry wind, and winter nights that drop near freezing combine to fatigue welds and shear bolts faster than in milder climates. Owners usually discover this kind of failure when the gate goes crooked, the arm pulls loose from the leaf, or the operator runs but the gate barely moves.
Which FAAC Models This Applies To
FAAC makes a broad line of residential and light-commercial swing and slide operators. The welding and fabrication work we do touches the hardware that surrounds the operator on most of them: 390, 391, 400, 422, 452, 540, 550, and the S418 and 844 slide-gate lines, along with older 760 and 770 swing units still running on plenty of properties around North Las Vegas. The operator box is rarely the problem. It’s the mounting brackets, gate arms, hinge plates, and posts that carry it all.
To identify exactly what you have, look for the data plate riveted inside the operator housing or under the cover, then measure the gate leaf width and the distance from the hinge to the operator arm pivot. Those two measurements decide the bracket and arm geometry far more than the model number does. On OEM versus aftermarket: for welding and fabrication, there’s usually no “OEM replacement part” to chase anyway. The original bracket either exists or it doesn’t, and when it doesn’t, we fabricate a match. When a factory-correct bracket or arm mount is still available, we’ll tell you. We’re an independent service company with no affiliation to FAAC, so our only reason to recommend a part is that it’s the right one for your gate.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Welding & Fabrication Is Failing
A failed weld rarely announces itself. It shows up as a gate that suddenly doesn’t line up right, or an operator that’s working harder than it should. Here’s what we see most often in North Las Vegas:
- The gate sags or drops at the hinge, not in the middle. That points to a fatigued hinge post or a cracked weld at the pivot plate. If the post is being asked to carry a leaf it can no longer support, the sag returns within weeks of any patch job.
- The operator arm pulls away from the gate leaf. The mounting bracket bolts or welds have failed. It’s usually caused by years of vibration against an under-built bracket, and it gets worse fast once the arm works loose.
- The gate runs and stops short, or reverses on its own. A cracked weld at the operator mount lets the base flex under load, throwing off the geometry the FAAC controller reads as position. The operator isn’t faulty; the mount is moving.
- Bolts won’t stay tight, or the threads strip out on retightening. The holes in the bracket or post have ovaled out. Re-welding and re-drilling a fresh bracket is a better fix than chasing bigger bolts.
- Visible rust bloom around a joint, or a hairline crack you can feel with a fingernail. In North Las Vegas, morning dew and irrigation overspray sit in seams and accelerate corrosion at the weld toe. If you can catch a crack now, the repair is small.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
On-site FAAC welding and fabrication repairs in North Las Vegas run $180 to $420 installed. What drives the range is labor and metal, not a markup on the part. A simple re-weld of a cracked bracket might sit at the low end; a bent operator mount that needs a custom cut and fabrication, plus grinding and refinishing, sits higher.
| Scope of work | Typical installed range |
|---|---|
| Re-weld cracked bracket or hinge plate | $180 – $260 |
| Fabricate and install replacement operator mount | $240 – $340 |
| Hinge post repair or sleeve, plus weld | $280 – $420 |
| Full bracket and arm-geometry rework | $420 and up |
That price includes the welding, the on-site labor, materials, and cleanup. It does not include a new operator or parts we don’t fabricate, and we’ll tell you upfront if any of those come into play. Every job is covered by our 90-Day Done Right Promise in writing, and the price you agree to is the price you pay.
DIY or Call Us?
There’s a safe portion of this you can handle yourself, and there’s a piece you shouldn’t. Before anything else, do this: turn off power to the operator and confirm the gate is fully stopped.
Safe to check yourself: power off and inspection, tightening visible bolts that are loose but not stripped, feeling for cracks at weld joints with a flashlight and a fingernail, and photographing damage before you call.
Not a DIY job: welding on a gate that carries an operator. Structural welds on a gate leaf or hinge post that holds a moving gate take heat, penetration, and post-weld alignment to be safe. On a driveway where a kid or a car could be under the gate, a bad weld is a real hazard. Replacing an operator bracket, correcting hinge geometry, and welding near an installed operator all want a trained hand. We fix it in one visit, typically the same day in North Las Vegas. Call (844) 761-9351 and tell us what you’re seeing.
FAQs
A properly fabricated and welded repair on a FAAC gate in North Las Vegas should last 10 to 15 years before the same joint shows fatigue, and often longer if the post and leaf are sound. The enemy here is heat cycling and dry-to-wet swings at the seams, so we clean and prep the joint right the first time rather than welding over rust.
Yes, in most cases, and we’ll tell you honestly when it can’t. A cracked bracket, a bent operator mount, a sagging hinge post: these are weld and fabrication repairs, not replacements. Replacing the whole gate is the wrong move when the weld is the problem. We fix the failing joint first and only recommend replacement when the metal itself is too thin or too fatigued to hold.
Most FAAC welding and fabrication repairs are a same-day, single-visit job, typically one to three hours on site. We weld in your driveway, so we’re not hauling your gate away and leaving you open. If the repair requires fabrication of a custom bracket, we’ll quote the time upfront and stick to it.
We fabricate most of what we need on site from structural steel matched to your gate, and we source factory-correct FAAC arms, brackets, and mounts when they’re available. We don’t claim to carry parts on a truck or stock FAAC parts locally. We confirm what’s needed, quote it, and get it right. Call (844) 761-9351 for a free second opinion on any written estimate you’ve already been given.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.