Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateBFT Gate Installation in North Las Vegas: What to Know First
We install BFT gate operators and the gates they drive for homeowners across North Las Vegas, and most jobs get measured one week and set the next. BFT is Italian-engineered gear, and the brands you’ll see here most often are the Ares and Deimos swing operators, the Phobos sliding operator, and the E5 for lighter swing gates. Our pricing is written down before we touch a bolt, and nothing extra shows up on the invoice later.
This page is for the homeowner who has a BFT operator sitting in a box, or a gate and operator that were spec’d but never set right, and wants a straight answer on what a proper BFT install looks like in North Las Vegas. Call (844) 761-9351 and a live person picks up.
How BFT Products Fail – and How We Fix Them
BFT operators are built well. The failures we see on them are almost always installation failures, not brand failures. Here’s what we run into on BFT jobs around North Las Vegas.
- Ares and Deimos swing arms binding in the heat. The Ares 1000 and the Deimos BT A400 are both spec’d for gates under a certain weight, and in summer heat the steel gate expands just enough to fight the arm. You’ll hear a groan or a stall, and the board may throw an overload fault. Fix is usually re-setting the arm geometry and checking the gate for a hinge-post sag, because a sag adds load the operator was never sized for.
- Phobos sliding operators slipping on the rack. On BFT Phobos and Phobos BT A series, a slipping slide manifests at the pinion and rack. The rack drops 3/16″ over a couple of years on a gate that sits on an uneven slab. We shim the rack, re-level the gate travel, and reset the limit cams rather than touching the gearbox.
- E5 swing boards frying after a voltage dip. The E5 is a light-duty swing operator; when a gate is too heavy or the control box is wired to a circuit that browns out, the board fails. Cause is undersized power run, not the operator. We run a properly sized dedicated circuit and install a surge suppressor before we ever put the board in.
- Limit switch error on a BFT setup installed with aftermarket hardware. When a BFT operator is paired with a non-BFT limit switch, the encoder and the switch talk past each other. You get a phantom “limit not reached” fault. We test with the OEM switch first; if the board wants OEM, we use OEM.
- Keypads and photo eyes that die from our wind-blown dust. North Las Vegas gets dust storms that pack the beam housing on BFT photo eyes and the reader slot on a keypad. Clean the eyes once a month, replace the rubber gasket on the housing at the first sign of cracking, and they last years longer.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our BFT Gate Installation Process
- 1
Walk the site and measure. We measure the gate leaf, check the post plumb, look at the slab, and verify the power source. A BFT operator spec’d against a crooked post will fail on you inside a season.
- 2
Size the operator to the gate, not to the price sheet. If the gate is 500 pounds, we don’t put the smallest BFT unit on it. We size the motor to the gate and tell you plainly what a proper unit costs.
- 3
Choose parts with the warranty in mind. OEM BFT boards and motors carry the manufacturer’s warranty. Quality aftermarket parts can save real money on a light-duty E5 job; on the Ares and Phobos we lean OEM because the board is what fails without it.
- 4
Set the operator. Bolt it in, wire the power and control runs, hang the arm or rack, set limits, pair the remote, and install the photo eyes and safety edges before we ever test the gate closed on its own.
- 5
Test the safety, not just the open. We trip the photo eye and the safety edge by hand and make sure the gate reverses every time before we hand the remote over.
- 6
Clean up and hand you the paperwork. Old boxes and offcuts go with us. The 90-Day Done Right Promise goes on the work order in writing, and I’ll be back on one call inside that window.
What BFT Gate Installation Costs in North Las Vegas
Real ranges for BFT work in North Las Vegas, based on jobs we’ve actually done. These are typical, not a quote.
| Job | Typical Range |
|---|---|
| BFT E5 swing install on an existing gate | $900 – $1,500 |
| BFT Ares 1000 or Deimos BT A400 swing install | $1,600 – $2,800 |
| BFT Phobos sliding operator install | $1,800 – $3,200 |
| Safety edges and photo eye addition | $350 – $650 |
| Dedicated power run (new circuit) | $600 – $1,200 |
| Board or motor replacement inside an install | $450 – $900 |
What moves the price: gate weight, whether the post is plumb, how far the power run has to go, and whether the rack or arm has to be re-fit. Every number above gets quoted and agreed on before we start, and it doesn’t change at the door. Free second opinion on any written estimate, and we don’t charge a trip fee inside the county.
Call (844) 761-9351 and we’ll set a time to measure and quote.
See the difference
Before
After
Before
After
Before
AfterWhy North Las Vegas Homeowners Call Gatewood Fence & Gate North Las Vegas for BFT Work
We’ve been locally owned and owner-operated since 2001, and the name is on the shop. We’re an independent BFT service provider – not authorized by the manufacturer, and not pretending to be. We know BFT because we’ve installed and serviced it, and our technicians have up to 25 years of experience. When we do a BFT job in North Las Vegas, the gate stays in your driveway; we weld and repair on-site when the repair calls for it, and we don’t swap parts that don’t need swapping.
If a job does call for something outside BFT, we also handle LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. Same standard. Same 90-Day Done Right Promise. Every job carries it in writing. Standing offers: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Calls get answered by a live person, 24/7. No voicemail, no queue.
FAQs
No – a proper install by a competent installer is exactly what BFT’s warranty expects. What does void it is running the operator on an undersized circuit or a gate that outweighs the unit, which is why we check both before we bolt anything down. Call (844) 761-9351 for a free estimate.
OEM BFT boards, motors, and remotes are available through US distribution, and lead times are usually days, not weeks. On rare parts we’ll tell you the honest wait rather than a number we can’t back up. Call (844) 761-9351 and we’ll tell you what’s in hand.
Almost never. On an Ares or Deimos, a half-open stop is nearly always a binding gate leaf or a limit setting, not a dead motor. We test the gate by hand first; if it binds, the operator was fine and the post needs attention. Call (844) 761-9351 and we’ll take a look.
Yes. Dedicated power, control wiring, photo eyes, and safety edges are part of the job, not a separate trade you have to line up yourself. We set and test the reverse on the safety edge before we leave. Call (844) 761-9351.
Measurements typically happen within a week of your call, and installation is scheduled once the operator and any parts are on hand. Install work is scheduled, not same-day; we don’t promise a dispatch window we can’t hit. Call (844) 761-9351 for a free estimate.
Get a Written BFT Install Quote
If you’re in North Las Vegas and you’ve got a BFT operator to install, or you want to know whether a repair beats a replacement, call (844) 761-9351. A live person answers, we set a time to measure, and you get a written price before any work starts.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.