Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Repair in North Las Vegas: What to Know First
Linear gate repair in North Las Vegas usually runs $185 to $420 for a stuck or failing operator, and $140 to $360 for hinge, post, roller, or alignment work, with most repairs done the same visit when the part is on hand. We’re an independent Linear service provider, not Linear the manufacturer, and we fix the gate in your driveway instead of selling you a new one. You’ll get a written price before we start, and it won’t change when we’re done.
This page is for the homeowner who already has a Linear operator on the post and wants it working again, not replaced. Call (844) 761-9351 and a live person answers, day or night.
We’re Hal Gatewood’s shop, Gatewood Fence & Gate North Las Vegas, and the name is on the door down the road. If the gate isn’t behaving, we want to hear what it’s doing.
How Linear Products Fail – and How We Fix Them
Linear is a workhorse brand, and it fails in specific ways. Thirty-plus years of desert heat, monsoon grit, and caliche soil take their toll on these drives and arms differently than on LiftMaster or Mighty Mule units. Here’s what we see most, and how we handle it.
- Linear Pro Access LDO/LSO swing arm drives. Continued use with a worn bushing or a dry pivot starts the arm chattering and grinding. When the arm bushing dries out, the operator arm binds and eventually strips the drive gear or throws the limit switch out of adjustment. We pull the arm, inspect the bushing and pivot pins, re-grease, and check the limit settings before we put it back. Usually $185 to $310 for the arm service plus any gear or limit parts.
- Swing gate operators with a slipping clutch. The clutch on these arms is designed to let go when it meets an obstruction, but dust and grit build up over a Vegas summer and it starts slipping on a gate that’s just a few pounds too heavy. We test the clutch force with a scale, not by feel, and correct the gate weight or the arm geometry before we touch the operator. A gate that’s come loose at the hinge is what’s really overloading the arm.
- Slide gate operators with rolling hardware that’s dropped or seized. Linear slide operators push through a track that’s supposed to be flat. Once a wheel flat-spots or a V-groove fills with decomposed granite, the motor takes the entire load and the control board overheats. We replace the wheel, re-level the track, and re-set the face or edge sensor. If the control board got cooked, we compare OEM versus quality aftermarket options before we order.
- Gate lock and latch failures on swing operators. The lock mechanism on a swing linear operator is paired with the arm, and when the lock solenoid fails, the operator throws a fault and refuses to move. We test the solenoid and the lock wiring first, then check the board’s fault code. A lock that’s missing its strike or misaligned with the post is a common culprit on driveways with settling concrete.
- Photosensor alignment and control board faults. Linear’s photoelectric sensors and control boards are sensitive to voltage spikes from our summer storms and to loose terminal screws after a wind event. When the gate reverses for no obvious reason, we check the photo eye, the board, and the safety edges, in that order, before we suggest a driver module or board replacement.
On every one of those, the fix is in the driveway. We weld, we realign, we re-grease, we replace only the failed part. A gate sags in the hinge post, not in the middle, and that’s where we start.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Linear Gate Repair Process
Here’s the shape of a Linear job from the first ring to the clean-up.
- 1
You call and a person answers. Not a queue, not a prompt tree. We ask what the gate’s doing, what model you have, and whether it’s stuck open or stuck closed. Same-day scheduling inside North Las Vegas when we can, next morning otherwise.
- 2
We come out and diagnose on site. We test the operator, cycle the gate by hand, and check the arm, the hinge posts, the track, and the board. If the gate is structurally unsafe or the operator is hot, we tell you right then and don’t run it.
- 3
You get a written price before any tool comes out of the truck. If it’s a $40 repair, you hear $40. If it’s a $340 repair, you hear that, and you hear why. The number doesn’t change at the door.
- 4
Parts decision. OEM when the part is available and worth it, quality aftermarket when the OEM part is on backorder or the design has a known weak point. We tell you which one we’re using and why.
- 5
We do the repair on site. Welding happens in your driveway. We don’t tow the gate, and we don’t replace parts that aren’t broken.
- 6
We run the gate at least a dozen full cycles, then check the safety edges and photo eye. Then we clean up. Every job comes with the 90-Day Done Right Promise in writing. If something isn’t right, one call brings us back.
See the difference
Before
After
Before
After
Before
AfterWhat Linear Gate Repair Costs in North Las Vegas
Prices below are what we actually quote in North Las Vegas, not a national average. A few things move the number: how old the operator is, whether the board is still available, and whether the gate’s structural problems are making the motor work too hard.
| Job | Typical price |
|---|---|
| Diagnostic and adjustment (limit, clutch, sensor) | $95 – $165 |
| Swing arm bushing, pivot, or gear service | $185 – $310 |
| Hinge and post repair (including weld) | $140 – $360 |
| Gate realignment (sag, drift, or dragged wheel) | $160 – $340 |
| Control board or driver module replacement | $260 – $540 |
| Lock solenoid or latch repair | $140 – $290 |
| Photo eye and safety edge repair | $120 – $260 |
Standing offers: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. If another outfit gave you a written estimate, we’ll give you a second opinion on it, free. Call (844) 761-9351 for an exact quote.
Why North Las Vegas Homeowners Call Gatewood Fence & Gate North Las Vegas for Linear Work
Three reasons. The first is that Hal’s been at this since 2001, and the shop is at a published address with a license number anybody can look up. When a gate fails in North Las Vegas, the person who shows up is not going to be a subcontractor you’ve never met.
The second is the 90-Day Done Right Promise. It’s printed on every invoice. If it’s not right, we come back, and there’s no runaround about it.
The third is Linear experience. Hal and his crew have worked on Linear swing arms and slide drives for years, and the person on the job can tell you what a slipping clutch on a Linear sounds like versus a failing drive gear. We’re certified on nine major gate brands, LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so if your gate has been swapped or the operator’s been changed, we’re not going to shrug at it. If you’ve already got a LiftMaster or a Mighty Mule on your property, we handle those too.
The last thing: no-hassle pricing. The number you hear is the number you pay. No setup fee, no “estimate might change at the door,” no haggling.
FAQs
No, as long as the repair is done by an independent service provider using compatible parts, and the operator isn’t modified outside the manufacturer’s specs. We use OEM Linear parts on warranty-relevant components whenever they’re available. Once the warranty has lapsed, we’ll talk through quality aftermarket options and let you decide.
Usually for the common parts, yes. Bushings, limit switches, photo eyes, and lock solenoids are the parts we keep most often. Control boards and driver modules sometimes need a day to order. We’ll tell you up front which category your repair is in.
Repair it if the operator is under about ten years old and the failure is a part, not the drive. An arm bushing, a limit switch, or a clutch is a repair, not a replacement. Replace if the drive motor burned out, the board is no longer manufactured, or the gate has structural problems that no operator can live with. We’ll show you the difference in writing before you decide.
Same day in most cases when you call before mid-afternoon, and next morning if you call later. Emergency calls are answered around the clock, and the person who picks up can schedule it. Call (844) 761-9351.
Both. A sagging hinge, a cracked weld, and a dropped roller are gate problems that make the Linear operator work harder until it fails. We fix the gate in the driveway, including on-site welding, so the operator isn’t carrying the problem anymore.
If your Linear gate is doing something it shouldn’t, call (844) 761-9351 for a free estimate. We’ll get out there, take a look, and give you a straight price before anything starts.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.