Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Gate Motor & Opener in North Las Vegas: What to Know First
We service and repair Linear gate motors and openers in North Las Vegas as an independent Linear service provider, which means we’re not tied to the factory, we’re tied to you. Most Linear repair jobs are diagnosed and fixed on the first visit; a full motor replacement or a new operator install gets measured, quoted in writing, and scheduled. You’ll know the price before we touch a thing, and that price doesn’t move at the door.
This page is for the homeowner with a Linear swing or slide operator who’s tired of a gate that stops halfway, an arm that groans, or a remote that only works when you’re standing in exactly the right spot. Call (844) 761-9351 and a live person picks up, day or night.
How Linear Products Fail – and How We Fix Them
Linear builds solid residential operators, and the ones in North Las Vegas homes are mostly the LSO and LCO swing series, the SWR slide operators, and the older LC series that hung on driveways out toward the 215. The failures are predictable once you’ve seen a few hundred of them, and each one tells you something the spec sheet won’t.
- Control-board corrosion on the LSO series. Our dry heat is brutal on the sun-exposed control box, then the summer monsoon blows in dust and the occasional hard rain, and that moisture sits on the board. Homeowners describe it as the gate “open and then forgetting how to close.” The board is usually the cause, not the motor. We test the board first, reseal the enclosure, and replace only the board if the motor windings are clean.
- Arm bushings wearing out on LCO swing operators. On a swing arm, the bushing at the gate bracket loosens over years of thermal expansion, so the arm slaps instead of pushing smooth. It sounds like a knock and feels like the gate hesitates mid-swing. We replace the bushings and re-hang the arm rather than selling you a whole operator.
- Limit-switch drift on the SWR slide operator. The roller chain on a slide gate stretches in the heat – it’s normal, nothing’s broken – and the travel limits drift with it. The gate over-travels or stops short. We re-set the limits against the actual gate, not a guess, and lube the chain with the right weight of grease so it doesn’t attract the desert grit.
- Battery backup dying quietly. Linear’s DC operators use sealed gel batteries in the backup circuit, and desert heat kills them in three or four summers instead of the seven or eight you’d get somewhere cooler. The symptom is the gate failing during a brief power blip – something North Las Vegas sees every storm season. We test the backup under a real load and swap the battery if it’s flat, so the backup actually backs you up.
- Entrapment sensors and edges going false. Linear operators rely on the safety edge to reverse on contact, and a cracked edge on a sun-baked gate will send a false signal – the gate stops mid-travel for no reason. It reads like a motor fault but it’s the edge. We test the edge, replace the rubber if it’s split, and re-verify the reverse force against the gate’s actual weight.
There’s a parts nuance worth knowing: Linear’s OEM boards and remotes are the right call for most LSO and SWR repairs because aftermarket boards have a shakier track record and can void the operator’s manufacturer warranty. On older LC-series units, though, some components are no longer stocked, and a quality aftermarket equivalent keeps a working gate working instead of pushing you into a replacement you don’t need yet. We make that call with you, not at you.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Linear Gate Motor & Opener Process
- 1
You call, a person answers. Not a queue, not a voicemail – someone with a notepad and a schedule. We ask what your Linear operator is doing and when it started, because that first description usually points straight at the board, the limits, or the backup.
- 2
We diagnose on site. Every Linear job gets the same sequence: check the power, the board, the motor windings, the arm or chain, the safety edges, and the battery backup. We watch what the gate does before we touch it. A gate that closes on its own tells us where it’s failing.
- 3
We decide OEM or aftermarket with you. If it’s a board, remote, or sensor under a valid Linear warranty, we lean OEM. If a discontinued part has a sound aftermarket match, we explain the trade-off and you choose.
- 4
We repair on site. Bushings, limits, chain tension, sensor edges, batteries – most of it happens in your driveway. No hauling the gate somewhere and disappearing with it.
- 5
We test it under real conditions. Open and close under load, reverse test on the safety edges, and a backup check with the power pulled. Then we walk you through everything we found.
- 6
We stand behind it in writing. Every job carries the 90-Day Done Right Promise, signed and stamped on the invoice. If it’s not right, you call once and we come back. No runaround.
What Linear Gate Motor & Opener Costs in North Las Vegas
Here’s what Linear service typically runs in the North Las Vegas market, with the honest ranges. We quote before anything starts, and the quote is the bill.
| Scenario | Typical range |
|---|---|
| Diagnostic visit (waived if you go ahead with the repair) | $0 trip charge inside the county; diagnostic credited to the job |
| Linear LSO control-board replacement | $180 – $340 parts and labor |
| Swing-arm bushing and bracket service (LCO series) | $140 – $260 |
| SWR slide-gate limit re-set and chain service | $120 – $220 |
| Battery backup replacement (DC operators) | $160 – $290 |
| Full Linear motor and operator replacement | Quoted in writing after measure, typically $650 – $1,400 installed depending on gate weight and travel |
What moves the price: gate weight and width, whether the operator is a swing or slide model, whether the concrete pad needs work, and whether we’re replacing a board or the whole operator. A full install is measured, ordered, and scheduled – we don’t promise same-day on a new operator, and we won’t pretend to. Estimates are free, and a second opinion on any written estimate you already have won’t cost you a nickel.
See the difference
Before
After
Before
After
Before
AfterWhy North Las Vegas Homeowners Call Gatewood Fence & Gate North Las Vegas for Linear Work
We’ve been locally owned and owner-operated since 2001, and the name is on the shop and on every invoice – you can drive down and look us in the eye. The person who answers the phone when your Linear gate quits at 10 p.m. is a live human, not a chatbot three states away. Our technicians have up to 25 years of experience, and they do the actual work on site: welding, repairing, re-hanging, not just swapping parts and leaving.
When it’s a Linear job, we bring the Linear-specific knowledge – the LSO board quirks, the SWR limit drift, the battery heat problem – and we back every job with the 90-Day Done Right Promise. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing when your property has a mix of brands, so you’re not calling four companies. And our standing line holds: $40 off any repair over $200, 10% off for seniors and veterans, free second opinion on any written estimate.
FAQs
It matters a lot, and it’s the first thing we check on any Linear job. Linear’s manufacturer warranty typically covers the operator for a set period from install, and using OEM parts keeps that warranty intact – while some aftermarket boards can void it. We look up your model and install date before recommending parts, so you don’t lose coverage you already paid for. Call (844) 761-9351 with your model number and we’ll tell you where you stand.
Most common Linear parts – boards, remotes, batteries, sensor edges – are available without a long wait, and we’ll tell you upfront if a specific component is backordered so you’re not guessing. On discontinued LC-series parts, we’ll offer a quality aftermarket match that keeps the gate running. Either way, you get the parts situation in writing before work starts.
Repair, most of the time. A board, a bushing, a limit switch, or a backup battery is usually a fraction of a new operator, and a Linear unit that’s still mechanically sound should be repaired, not scrapped. We only recommend replacement when the motor windings are burned, the gearbox is stripped, or the gate geometry has outgrown the operator. We’ll show you the difference on site and let you decide – we don’t push replacements.
Repair calls are usually seen the same day or next, and emergencies get priority – a gate stuck open is a security problem, not just an inconvenience. New Linear operator installs are measured and scheduled around your timeline, typically within a week or two depending on the model. Either way, a live person answers when you call (844) 761-9351, including overnight and weekends.
Yes – both are part of our standard Linear checklist, not an add-on. We test the DC backup under a real load and verify the safety edges reverse the gate on contact, which is a genuine safety matter, not a formality. A gate that doesn’t reverse on an obstruction can hurt someone, so we don’t skip it. Call (844) 761-9351 and we’ll walk through what your Linear operator needs.
Get Your Linear Gate Fixed Right
If your Linear gate is stopping short, forgetting to close, or running on a backup battery that’s given up, give us a call. We’ll diagnose it, quote it in writing, and fix it right – with the 90-Day Done Right Promise stamped on the invoice. Free estimates, no trip charge inside the county, and a live person on the line 24/7. Call (844) 761-9351 for a free estimate today.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.