Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Hinge & Roller Replacement: The North Las Vegas Owner’s Guide
We replace failed Ghost Controls gate hinges and rollers with compatible parts, and a typical installed job in North Las Vegas runs $145 to $320 depending on how many hinges and rollers your gate uses and whether the hinge post needs welding. Same-day repair is often possible when you call early. Most owners here don’t discover this part has failed until the gate starts dragging on the driveway, hangs at an angle when it’s open, or the opener begins straining and stalling partway through a cycle. By the time the motor complains, the hinge has usually been worn for months. Our technicians have up to 25 years of experience, and we’re certified to service Ghost Controls along with LiftMaster, Mighty Mule, and DoorKing.
Why hinges and rollers wear faster in the desert
North Las Vegas gates live in blowing grit, 110-degree summers, and hard temperature swings between afternoon and night. Dust works into hinge pins and roller races and turns into an abrasive paste, then the monsoon arrives and pushes it deeper. That’s a big part of why we see hinge and roller wear here earlier than owners expect.
Key Takeaways
- Installed Ghost Controls hinge and roller replacement in North Las Vegas typically runs $145-$320.
- Same-day repair is often available; call early in the day.
- We identify your exact Ghost Controls model before quoting, because the parts aren’t universal across the line.
- Worn hinges stress the opener motor. Fixing the hinge early protects the operator.
Which Ghost Controls Models This Applies To
Ghost Controls builds a lot of its residential line on a shared tube-and-frame platform, and many hinge and roller components cross between models. But not all of them. Before we quote anything, we read the model and serial sticker, usually inside the control box cover or on the rear frame member, and match the part to that model rather than to a photo the owner texted us. A gate that looks identical from the street can carry different hinges.
Ghost Controls uses a mix of bolt-on hinge brackets and welded or bolted roller assemblies, and the exact tube diameter and hinge-pin spacing vary by series. That’s the compatibility gotcha most buyers hit online: a generic “fits Ghost Controls” hinge often has the right look and the wrong bolt pattern or pin diameter. It’ll bolt on, then wear out in a season because it never sat flush.
OEM or aftermarket?
For Ghost Controls specifically, OEM hinges and rollers are the safest fit if your model is still supported. When it isn’t, quality aftermarket equivalents do exist, but only if the pin diameter and bracket geometry match. We’ll tell you honestly which way we’d go for your gate. We don’t claim stock of any parts, so we confirm the exact part number with you before we order or install.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Hinge & Roller Replacement Is Failing
- Gate sags when open. A worn hinge pin or an elongated bolt hole lets the gate drop at the hinge post. If it only sags when open, the hinge is the suspect, not the frame.
- Rollers that flat-spot or bind. Desert grit gets into the roller race and the wheel stops turning cleanly. You’ll hear a scrape or feel a catch as the gate travels.
- Opener straining or stalling mid-cycle. A dragging hinge forces the motor to fight the gate. The opener is usually the messenger, not the cause.
- Visible play at the hinge. Grab the gate and rock it. If there’s slop at the pin or bracket, the hinge is worn and it will only get worse.
- Rust streaks or fresh paint over old wear. Sometimes the last repair was paint over a failing hinge. We see this in North Las Vegas more than you’d think, and it hides the real problem for a season.
Here’s the pattern we’ve learned: a gate sags in the hinge post, not in the middle. That’s where we start, every time. Fix the panel without the post and you’ll fix it twice.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
We quote installed prices, parts and labor together, so you’re not chasing a separate parts invoice. Upfront pricing is agreed before any work starts, and it doesn’t change at the door.
| Job | Typical installed range |
|---|---|
| Single hinge replacement | $145-$195 |
| Pair of hinges (both posts) | $195-$260 |
| Roller set replacement | $150-$220 |
| Full hinge and roller refresh, one leaf | $240-$320 |
| Hinge post welding if the post is compromised | Quoted on site |
What drives the range: number of hinges and rollers, model, whether the hinge post needs on-site welding (Hal welds in your driveway, so the gate stays put), and whether the gate is a single swing, double swing, or slide. Every job carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings us back.
DIY or Call Us?
Some checks are safe for an owner. You can rock the gate by hand to feel for hinge play, look for flat spots or binding on the rollers, and look for rust streaks at the hinge brackets. What you shouldn’t do yourself is remove a hinge on a gate that’s already free-standing at load, weld a post, or chase a bolt pattern that doesn’t match. A swinging gate carries real weight, and if a hinge lets go while you’re working under it, that’s a hospital visit, not a repair. That’s the honest line. We’re not going to scare you, but we will tell you plainly: a gate that sags and binds is not a weekend bolt-on.
Call (844) 761-9351 for a free estimate. A live person answers, day or night.
FAQs
Expect five to eight years on a residential gate in North Las Vegas with routine lubrication, and shorter where grit blows across the driveway and the gate runs hard. Rollers tend to go first in sandy lots and near new construction grading, because grit gets into the race before a hinge pin shows wear.
Sometimes, yes. A tight hinge can often be re-bushed, a bound roller can be cleaned and re-greased, and a bracket can be re-torqued. When the pin is worn oval or the race is scored, replacement is the right call, and we’ll tell you which it is rather than swapping parts it doesn’t need.
A single hinge or roller set is usually an hour to 90 minutes. A full refresh on one leaf plus a post weld can run most of an afternoon. We give you a realistic window when we book, and we show up in it.
We identify your exact model and serial first, then source the correct OEM or a fitting aftermarket equivalent and confirm the part number with you before any work. We’re an independent service provider. We’re not affiliated with Ghost Controls, but we’re certified to service Ghost Controls along with eight other major gate brands, and we’ve been working on them long enough to know which fit will hold and which won’t.
Ready? Call (844) 761-9351 for a free estimate. A live person answers 24/7, no trip charge inside the county, $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.