Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Welding & Fabrication: The North Las Vegas Owner’s Guide
Welding and fabrication work on a Ghost Controls gate in North Las Vegas usually runs $180 to $420 installed, and for a gate that’s stuck open or dragging, we can often get out the same day you call. Most owners don’t go looking for this service until something loud happens: a hinge bracket tears off the post with a bang, the gate drops and scrapes the driveway, or an arm mount bends and the opener starts shoving the gate sideways instead of swinging it. You walk outside, see the gap, and the gate won’t latch. That’s when the phone comes out. A live person answers at Gatewood Fence & Gate, day or night, and we’ll tell you straight what we think it is before anybody drives out.
In North Las Vegas, we see a specific pattern. The dry heat and the sun load on a west-facing gate work the metal hard – expansion in the afternoon, contraction overnight – and a weld or bracket that was marginal when it went in starts to crack. Add a few summers of that and a Ghost Controls opener pushing a gate it was never quite matched to, and the weak point shows up fast.
Which Ghost Controls Models This Applies To
Ghost Controls makes its name on solar-friendly, DIY-oriented openers – the TSS1 single-gate kit and the DTP1 dual-gate kit are the two lines most North Las Vegas homeowners end up with, and both bolt to a gate through the same family of brackets and mount plates. The fabrication side is universal: hinge posts, arm mounts, gate frames, drop rods, and latch receivers. The part that has to match is the mounting interface, and the way to identify yours is by the label on the control box and by measuring the arm mount plate, not by trusting what the last installer told you.
Here’s where Ghost Controls gets particular. The arm mount plate and the operator bracket set are tied to the gate’s geometry – post-to-gate gap, and whether the gate swings in or out – and a bracket that’s a half-inch off will fight the opener for the life of the gate. We measure before we cut anything.
On OEM versus aftermarket: for the structural welding and fabrication, there’s no meaningful OEM option – the brackets that fail are generic steel, and we fabricate or match a hardened equivalent on site. For anything Ghost Controls-specific like the arm or the control board, if it’s failing, we source the correct Ghost Controls part rather than forcing a universal fit. Gatewood Fence & Gate North Las Vegas is an independent service provider and not affiliated with Ghost Controls; we service the brand because we know it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Welding & Fabrication Is Failing
The failure doesn’t announce itself. It builds. Here’s what we look for, and what it usually means:
- A visible crack at the hinge or arm-mount weld. Heat cycling and the opener’s push-pull flex fatigue the weld over seasons. A hairline crack at the toe of the weld is the first thing we find, and it only widens once it’s loaded.
- The gate sags and drags the ground. A sagging gate usually means movement at the post, not the panel. If the hinge post has shifted or rusted through at the weld, the whole gate drops, and no amount of adjusting the Ghost Controls arm will fix it.
- The opener groans or the arm looks like it’s fighting the gate. A bent or misaligned arm mount throws the geometry off, so the Ghost Controls arm pushes at an angle instead of straight. That noise is metal binding.
- Rust streaming from a joint after rain. North Las Vegas is dry, but our occasional monsoons push water into every unsealed weld, and paint over a bad weld traps it. Rust bleeding out of a joint means water is already inside the steel.
- The gate won’t latch or the latch receiver is loose. A weld at the latch post or receiver has let go. The gap at the latch is a symptom; the broken weld behind it is the cause.
Show me the gate closing on its own and I’ll show you where it’s failing. The way it drifts tells you which joint is tired.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Welding and fabrication on a Ghost Controls gate in North Las Vegas breaks down like this:
- Weld repair at a hinge, mount, or latch post: $180 to $320, on site.
- Arm mount or operator bracket fabrication and fit: $220 to $420, measured and matched to your gate.
- Hinge post repair or replacement: $250 to $500 depending on whether the post is set in concrete or bolted.
- Gate frame section rebuild: $300 to $600 for heavier fabrication.
What drives the range is how much has to come apart to do it right, and whether the post itself has moved. Hal fixes the gate in your driveway rather than hauling it off – on-site welding keeps your gate where it belongs. The part plus the labor is on one line and quoted before we strike an arc.
Every welding and fabrication job carries the 90-Day Done Right Promise in writing: if it’s not done right, we make it right. And there’s $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans – standing offers, no haggling. If you’ve got a written estimate from someone else, bring it and we’ll give you a free second opinion.
DIY or Call Us?
There’s a line here, and it’s worth being honest about it.
You can safely check the gate by hand: push it through its swing with the opener off and watch where it binds, look for cracks at the weld toes with a flashlight, and check whether the arm mount is bent. That tells you whether you’re dealing with a weld or an opener problem, and it’s useful to know before you call.
Welding is where we ask you to put it down. Gate frame steel is under load, and grinding or welding on a loaded, sagging gate without supporting it – and without knowing the metal’s thickness – is how people get hurt and how a small crack becomes a torn panel. The garage-door-spring parallel applies: a gate under tension will move when you relieve it, and you want a trained hand on it. We’re certified to service nine major brands, Ghost Controls included, and our technicians have up to 25 years of experience. Call (844) 761-9351 and we’ll take a look – upfront pricing, no surprises.
FAQs
A properly welded and sealed repair on a gate that’s set correctly holds for years, but the lifespan depends on the metal’s condition and whether the underlying binding got fixed. In North Las Vegas sun, the paint and the weld seal matter as much as the weld itself – we don’t just weld it and walk away, we close the seam so water can’t get back in. If the gate is still dragging because the post is shot, the weld is only half the job, which is why we check the post first. Call (844) 761-9351 for a straight answer on yours.
Almost always, yes. Most of what we see on Ghost Controls gates is a failed weld, a bent mount, or a dropped hinge post – all repairable on site without pulling the gate or swapping the opener. Fix the panel without the post and you’ll fix it twice, so we repair the whole assembly, not just the visible crack. We’d rather weld your gate than sell you a new one.
A straightforward weld or mount repair is usually done in a couple hours on site, same day in most cases. Heavier fabrication or a hinge post that has to be reset in concrete may run into a second visit once the concrete cures. We’ll tell you which before we start so you’re not guessing. Call (844) 761-9351 and we’ll give you a real window.
For anything Ghost Controls-specific, we source the correct Ghost Controls component for your model rather than forcing a universal fit; for structural fabrication we match the steel to what’s on your gate. We don’t claim to keep parts in stock or carry them on a truck, so if a specific part has to be ordered we’ll tell you the lead time up front. The quote is agreed before any work starts, and it doesn’t change at the door.
If your Ghost Controls gate is cracked, sagging, or fighting its opener, pick up the phone and let’s sort it out. We answer around the clock, and the person who shows up is the person whose name is on the shop. Call (844) 761-9351 for a free estimate on your welding or fabrication job in North Las Vegas – we’re proud to serve our local communities and happy to show you exactly what we find.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.