A Gatewood company - serving North Las Vegas, NV

DoorKing Gate Repair in North Las Vegas, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

DoorKing Gate Repair in North Las Vegas: What to Know First

We provide independent DoorKing gate repair in North Las Vegas, and most residential swing and slide gate calls get diagnosed and fixed in a single visit. You’ll get a written price before any tool comes out, and it doesn’t move at the door. Common jobs run from $185 to about $650, depending on whether we’re realigning a sagging gate or rebuilding a slide gate that’s been dragging for a season. We’re an independent DoorKing service provider – not affiliated with or authorized by DoorKing – and this page is for owners whose gate is stuck open, slamming shut, or quitting halfway. Call (844) 761-9351 and a live person answers.

Call (844) 761-9351

How DoorKing Products Fail – and How We Fix Them

DoorKing makes a heavy, well-built operator. What we see failing in North Las Vegas isn’t usually the electronics failing first – it’s the gate frame and the hinges dragging the operator into an early death. Here are the five we run into most.

  • Model 6400 slide gate – wheels and track wear before the motor does. On a long slide gate, the carriage wheels flatten and the track fills with desert grit, so the operator strains to push a gate that’s essentially dragging on the ground. Owners call us convinced the motor is burned out. Usually it isn’t; replacing the wheels, clearing the track, and resetting travel cures it. If we replace the operator without fixing the roll, the new one dies the same way.
  • Model 4500 and 4600 swing gates – hinge-post lean and the “closes on its own” symptom. When a steel post loses a couple of degrees of plumb, the gate swings open or closed under gravity and the operator fights it every cycle. That’s the sag living in the hinge post, not the middle of the gate. We pull it back to plumb and weld the post’s footing – on site, in your driveway – rather than swapping the control board the symptom points to.
  • Older 9000-series residential operators – control board and limit-switch drift. On these units, a slow, intermittent partial stop is a classic early warning of a limit switch drifting out of position. We reset the limits and test each stop before assuming the board is gone. A lot of these boards get replaced when a five-minute adjustment was the whole problem.
  • Model 6050 and 6100 commercial-grade units on long driveways – loop and detector false trips. North Las Vegas’ afternoon heat and sun load on a driveway loop trigger phantom opens. We test the loop and detector under real sun, trace the wiring, and either reseat the loop or re-tune the detector rather than guess at the board.
  • Every DoorKing made – the operator gets blamed for what the gate is doing. A gate that’s sagged or stiff makes even a healthy operator sound broken. Our first move is always to open the gate by hand and feel the resistance, because the seal, the weld, and the hinge, not the box, is usually what’s actually failing.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our DoorKing Gate Repair Process

Here’s how a DoorKing call actually runs, start to finish:

  1. 1
    You call, a live person answers. Not a voicemail, not a call center three states away. We take the brand, model if you know it, and what the gate is doing.
  2. 2
    We diagnose on site. Open the gate by hand, check post plumb, inspect the carriage or hinges, test the operator under load, and test any loops or safety edges. You’ll see exactly what we see.
  3. 3
    Parts decision, in front of you. If it’s an OEM DoorKing board or limit assembly, we say so and explain the cost. If a quality aftermarket part does the same job for less, we say that too. You decide with the price in your hand.
  4. 4
    The repair. Welding, realignment, and operator work happen in your driveway. We don’t haul the gate off or swap parts that don’t need swapping.
  5. 5
    The test. We cycle the gate through a full open/close under real conditions before we call it done. Show us the gate closing on its own during the test and we’ll show you what’s still failing.
  6. 6
    90-Day Done Right Promise, stamped in writing. If it’s not done right, one call brings us back. No runaround, no fine print.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What DoorKing Gate Repair Costs in North Las Vegas

Here’s what common DoorKing jobs run in the North Las Vegas area. These are ranges, not quotes – your exact price comes in writing before we start.

Job Typical range
Hinge, wheel, or roller replacement + realignment $185 – $340
Hinge-post realignment and on-site weld $240 – $420
Limit switch / travel reset $150 – $260
Control board replacement (parts + labor) $340 – $620
Safety-edge or loop repair $220 – $480
Weld and rust repair $180 – $400

What moves the price: OEM vs. aftermarket parts, the model line, whether welding is needed, and how far out your driveway is. Standing offers apply – $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. The price we quote is the price you pay. Call (844) 761-9351 – estimates are free.

Why North Las Vegas Homeowners Call Gatewood Fence & Gate North Las Vegas for DoorKing Work

Gatewood Fence & Gate has been locally owned and owner-operated since 2001, with our name on the shop and the shop down the road. That’s the oldest accountability there is. Our technicians have up to 25 years of experience, are background-checked, and are certified to service nine major gate brands – DoorKing, LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, Elite, and Mighty Mule – so if your gate turns out not to be DoorKing, we’re not handing you off. We fix what’s actually broken instead of swapping the whole operator, and every job is backed by the 90-Day Done Right Promise in writing. When it’s a genuine replacement, we tell you why – and we still pressure-test the diagnosis first. You can drive to the shop and look us in the eye.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (844) 761-9351
Local Service Coverage

Request a Free Estimate in North Las Vegas

Tell us what you need - Gatewood Fence & Gate North Las Vegas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch