Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Access Control Installation: The North Las Vegas Owner’s Guide
Elite-compatible access control installation in North Las Vegas typically runs $450 to $1,800 installed, depending on the Elite operator you’re running and the entry method you choose, and most of it is scheduled work we measure and price in writing before anything is ordered. We install keypads, card readers, telephone entry and vehicle-loop systems matched to Elite slide and swing operators, and we can usually get a free measure on the calendar within a few days. Calls are answered by a live person 24/7 when you’re stuck at a gate that won’t respond.
Owners rarely wake up one morning and decide to install access control. What usually happens is smaller and more annoying. A keypad starts eating codes. The gate opens from the car remote but not from the keypad, or only when it’s cool out. Somebody’s adult kid moves back in and you want the gate to stop answering their old code. In Sun City Aliante we see a lot of this in summer, when the keypad gets full sun on a west-facing pillar and the buttons go mushy by August.
We’re Gatewood Fence & Gate North Las Vegas, an independent service provider. We’re not affiliated with Elite, which is exactly why we’ll tell you honestly when the control hardware is fine and the operator is the problem.
Which Elite Models This Applies To
Elite makes residential slide and swing operators, and the access control hardware that bolts onto them is mostly universal on the low-voltage side. What changes between models is how the operator receives that signal. Elite slide operators typically accept a dry-contact closure and have dedicated accessory terminals for a receiver, keypad, loop detector or intercom, and the factory wiring diagram for your model tells you which pair does what. We check the model plate on the operator housing, not the label on the transmitter, because transmitters get replaced and the plate doesn’t lie.
Here’s the compatibility gotcha that bites North Las Vegas owners: shared single-channel receivers. If someone in the past added a cheap receiver to get a second remote working, it may be wired in series with the keypad and will fight it, so the keypad works until the receiver times out, then stops. We see that across the north valley more than any other single wiring fault.
On the OEM question: Elite-branded accessories fit cleanly and cost more. Quality aftermarket keypads and loop detectors work fine on the dry-contact side and run 30 to 50 percent less. The places we won’t substitute are the power supply and the operator interface board. Those are where a mismatch gets expensive. If you’re replacing a whole entrance rather than one wall unit, we also handle LiftMaster, Mighty Mule and Ghost Controls, so the recommendation is based on your gate, not on brand loyalty.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Elite Access Control Installation Is Failing
- The keypad works sometimes and not others. Usually a power supply on its way out or a moisture-damaged keypad board. Intermittent is almost always electrical, not a code problem, and North Las Vegas monsoon-season humidity finds every gap in an old gasket.
- The gate opens from the remote but ignores the keypad. The operator is fine. The signal path between keypad and operator is broken or the receiver is wired ahead of it. This is the most common single complaint we get and the cheapest to fix.
- Codes stop saving, or the keypad forgets them overnight. The memory chip in the keypad is failing. Once it starts, it never gets better, and every re-program is a band-aid.
- The gate won’t fully close, then reopens on its own. A vehicle loop detector is misreading, seeing phantom metal or losing its tuning. Common where the driveway cracked or a slab was poured over the loop.
- You can hear the operator click but the gate doesn’t move, and the keypad light dims when you press it. Low voltage on the accessory circuit. Something drew more current than the transformer supplies, often a second reader added later without anyone checking the load.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed price depends on how much of the entrance you’re replacing. Here are the ranges we work from in North Las Vegas, quoted as a flat installed figure. Estimates are free, and the price is quoted and agreed before anyone picks up a tool.
| Scope | Typical installed range |
|---|---|
| Single keypad replacement, wired to existing operator | $450 – $700 |
| Keypad plus power supply and rewiring of the accessory circuit | $700 – $1,100 |
| Vehicle loop detector install (cut, set, tune) | $650 – $1,200 |
| Card reader or telephone entry unit, residential | $1,100 – $1,800 |
| Full entrance conversion on an Elite slide or swing operator | $1,600 – $3,200 |
What drives the range: trenching distance from the house to the gate, whether conduit already exists, whether the driveway is concrete, asphalt or gravel, and how much of the existing low-voltage run is reusable. Loop work costs more on a fresh slab than on an old one.
Everything carries our 90-Day Done Right Promise in writing. If it’s not right, one call brings us back. Seniors and veterans get a permanent 10% off, and there’s no trip charge inside the county.
DIY or Call Us?
Some of this is safe to check yourself, and we’d rather you check it than pay a service call for nothing. Look at your operator’s model plate. Confirm the keypad has power by watching the light when you press a button. Write down whether the failure is constant or only at certain times of day. That information is genuinely useful to us and takes five minutes.
Where DIY goes wrong: the low-voltage side of an Elite operator is not dangerous, but the line-voltage feed from the house to the transformer is. There’s 120 volts entering that circuit, often through conduit somebody buried without a marker, and we’ve pulled more than one out of a North Las Vegas yard where the insulation had cracked and been sitting wet for years. We’d rather you not open that box. The other reason to call is the loop detector: getting the wire set and tuned right the first time saves you a return trip.
Call us at (844) 761-9351 and we’ll walk through it with you on the phone before we ever schedule a truck. Sometimes it’s a setting. Sometimes it’s a part. We’ll tell you which.
Frequently Asked Questions
Expect 6 to 10 years for a quality keypad on a shaded pillar, and closer to 4 or 5 for a unit in direct afternoon sun. UV and thermal cycling are what kill them, not use. A north-facing install gets you the full life; a west-facing gate on a block wall in the heat gets half. Call (844) 761-9351 for an exact quote, and the estimate is free.
Often a repair will do, and we’ll tell you honestly instead of swapping a unit that has years left. Keypads can usually have their board or power supply replaced rather than the whole unit. Where repair stops making sense is when the keypad housing is cracked and moisture is getting in, because the new board will follow the old one within a season. The price is quoted and agreed before any work begins, so you’ll know which way we lean and why.
A straight keypad replacement is usually 1 to 2 hours on site, and a loop detector install is 2 to 4 hours because the saw cuts and tuning take time. Card readers and telephone entry units are scheduled work, typically a half-day, and we measure first so the right parts come with us. Call (844) 761-9351 to get on the schedule.
We match the part to your Elite operator’s model plate, not the label on your transmitter, and we order against that. Our technicians have up to 25 years of experience, and they know which aftermarket keypads and loop detectors hold up in the desert and which don’t. We don’t carry parts on a truck, so the parts come ordered and matched. That’s also why we don’t promise same-day on a new install: measure and written price first, then the work.
You’re welcome to drive out to the shop and look us in the eye before you commit to anything. The name is on the shop and on every invoice, and we’re proudly serving local communities for over 29 years. Call Gatewood Fence & Gate North Las Vegas at (844) 761-9351 for a free estimate on your Elite access control installation, and we’ll get a live person on the line today.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.