A Gatewood company - serving North Las Vegas, NV

Elite Hinge & Roller Replacement in North Las Vegas, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Elite Hinge & Roller Replacement: The North Las Vegas Owner’s Guide

We replace worn or failed hinges and rollers on Elite gates with Elite-compatible hardware, and installed cost in North Las Vegas typically runs $140 to $320 for a pair of hinges or a roller set, depending on model and hardware grade. For gate repair calls in our service area, same-day visits are often available when you call in the morning. Licensed & insured, free estimate, and the price is quoted and agreed before any work starts.

Call (844) 761-9351

Most North Las Vegas owners don’t discover a hinge problem by looking at the hinge. They discover it when the gate starts rubbing the ground on the swing side, when the latch won’t catch without a yank, or when a roller squeals loud enough to hear from the kitchen window. A hinge that’s worn lets the gate drop a fraction of an inch at the post. Multiply that fraction across a wide gate and you get a gate that drags, sticks, or stops lining up with the strike. That’s usually the moment the phone comes out.

Which Elite Models This Applies To

Elite builds a range of residential and light commercial swing gate hardware, and hinge and roller form factors change between lines and revisions. We confirm the fit before we quote by matching the failed part to the gate’s hardware, not by guessing from the gate’s age. Two specs matter most: the hinge barrel and pin diameter, and the mounting hole pattern on the post bracket. A hinge that looks identical can have a pin 1/16 inch off, and that quarter-inch matters over a six-foot gate swing.

Here’s how to identify what you have. Look for the Elite label or model stamp on the gate hardware plate or on the operator arm housing. If there’s no label, measure the hinge pin diameter with calipers and photograph the bracket from the side. We also ask about the gate leaf weight and width, because Elite spec’d different hinge grades for different load classes. That’s the compatibility gotcha most North Las Vegas owners hit: buying a hinge that’s right for a lighter door on a gate that swings 250 pounds.

The OEM-vs-aftermarket call depends on the gate. For high-cycle gates, we lean OEM or OEM-equivalent because the metallurgy and pin hardness are known. For a light residential gate that cycles a few times a day, a quality aftermarket hinge at a lower price can last just as long. We’ll tell you which is which for your specific hardware and we won’t push OEM if aftermarket makes sense. Gatewood Fence & Gate North Las Vegas is an independent service provider, not affiliated with Elite.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Elite Hinge & Roller Replacement Is Failing

Hinges and rollers fail slowly, then all at once. These are the symptoms we hear most often when North Las Vegas owners call about a gate that used to glide and now doesn’t.

  • The gate sags at the hinge post. The hinge bore has worn oversized, letting the pin rock. A gate sags in the hinge post, not in the middle, and that is where we start looking.
  • Metal-on-metal squeal or grinding. The roller bearing has lost its grease, or the hinge pin is dry and pitted. Left alone, that grinding wears flat spots into the roller and chews the pin.
  • The latch won’t line up without lifting. The gate has dropped vertical alignment because of hinge wear, so the fork misses the strike. Owners often tighten the latch first; the latch is fine, the hinge is the culprit.
  • Visible rust streaks or pitting on the hinge plate. North Las Vegas heat and the occasional monsoon soak cycle the metal hard. Rust under the powder coat pops the finish and starts the pin seizing.
  • The roller rides off the track edge or thumps as it passes a joint. The roller wheel has gone out of round or the bracket bent. A bent bracket usually means the gate was struck or the hinge let it sag into the stop.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing for Elite hinge and roller replacement in North Las Vegas:

  • Single hinge replacement (one hinge, one post bracket): $95 – $165
  • Hinge pair replacement (both hinges on one gate leaf): $160 – $280
  • Roller set replacement (both rollers on one leaf): $120 – $220
  • Full hardware refresh (hinges and rollers on one leaf): $240 – $380
  • Heavy or commercial-grade Elite hardware, add: $40 – $90

What moves the number: gate leaf weight, whether the gate needs to come off its hinges to swap the hardware, whether the post bracket is welded or bolted, and whether the bolt holes are rusted or stripped. We quote parts and labor as one installed price, and you approve the number before we pick up a wrench. If a hinge can be re-pinned instead of replaced, we’ll tell you and charge less. The 90-Day Done Right Promise is stamped in writing on every job, so if a hinge fails in the first 90 days, one call brings us back.

DIY or Call Us?

There’s no high-tension spring or live electrical work in a hinge and roller swap, so this one sits about mid-range on the risk scale for gate work. What makes it go wrong for owners is a gate leaf that weighs 150 to 300 pounds and can fall if it’s not blocked or supported. Every year, a North Las Vegas homeowner gets a finger or a foot crushed by a gate they thought was lighter than it was.

Safe for an owner to check: whether the hinge pins are dry and squealing, whether the gate is dropping at the post, and whether roller bolts are loose. Safe to fix yourself: greasing a dry pin, snugging a loose roller bolt. Where DIY goes wrong: pulling a hinge pin when the gate isn’t blocked, or reaming a worn hinge bore to fit a bigger pin without knowing the bracket’s spec. Both can leave the gate leaning on the post. We bring the right pin, the right bracket, and we check the whole gate while we’re there. Call (844) 761-9351 and we’ll tell you honestly whether it’s a hinge, a roller, or something else before anyone shows up.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (844) 761-9351
Local Service Coverage

Request a Free Estimate in North Las Vegas

Tell us what you need - Gatewood Fence & Gate North Las Vegas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch