Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Gate Motor Replacement: The North Las Vegas Owner’s Guide
Mighty Mule gate motor replacement in North Las Vegas typically runs $575 to $1,150 installed for a residential swing gate, parts and labor together, and we can usually get to most North Las Vegas addresses within a day or two of your call. The price depends on which Mighty Mule model you have, whether the control board and battery survive, and how the gate itself is hanging. (More on that last one in a minute, because it’s the thing that kills more motors than anything else.)
Most owners don’t wake up knowing the motor is done. They notice the gate stopped halfway one morning and reversed. Or the arm started grinding at the top of the swing. Or they came home to a gate standing wide open and a click, click, click that goes nowhere. You push the remote a dozen times, wiggle the battery connections, and start searching for answers at 9 p.m. That’s usually where we come in.
Key Takeaways
- Mighty Mule motor replacement usually lands between $575 and $1,150 installed in North Las Vegas, quoted in writing before we start.
- Mighty Mule makes low-voltage DC swing openers for residential gates – the failure you’re seeing is almost always the control board, battery, or a stripped gear in the arm, not the whole unit.
- We service Mighty Mule alongside LiftMaster, Ghost Controls, and DoorKing, and we’re an independent shop – not affiliated with Mighty Mule.
- Every replacement carries the 90-Day Done Right Promise in writing, and we answer the phone around the clock.
- Our technicians have up to 25 years of experience with gate automation.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Which Mighty Mule Models This Applies To
Mighty Mule’s residential line covers a lot of ground, and the model matters when we’re matching parts. The most common units we see in North Las Vegas yards are the Mighty Mule 350, 360, 500, 550, and 600 series swing openers, plus the MM560 and MM660 arms and the newer Mighty Mule smart-control versions of those same machines. The single-arm units handle one gate leaf; the dual-arm units run a pair.
Here’s how to figure out what you have before you call. Look for a silver sticker on the control box or on the arm – it’ll show the model and a serial number. If the sticker has faded (very common in North Las Vegas sun), measure the arm housing end to end and note whether your unit is a single or dual setup. That’s usually enough for us to identify it. The other detail that matters is whether your opener is a slide or a swing unit, because the two replacement paths don’t overlap.
On the OEM-versus-aftermarket question, we’ll be straight with you: for Mighty Mule control boards and arms, genuine parts are the right call on most jobs. The aftermarket boards we’ve seen fail faster, and the firmware on the control board needs to talk to the arm and the safety sensors without argument. If your unit is old enough that the exact board is discontinued, we’ll tell you what the equivalent is and what it costs before we order anything. Nothing gets ordered, and nothing gets installed, until you’ve said yes to a written price.
Signs Your Mighty Mule Gate Motor Replacement Is Failing
Owners usually catch one of these five symptoms first. Each one points somewhere specific, and we’ve heard every one of them on the phone this month.
- The arm grinds or squeals when it moves. That’s usually a stripped gear inside the arm housing or a dry pivot point. A gear that’s already chewed up doesn’t heal with grease – it just gets louder.
- The gate stops halfway and reverses. Nine times out of ten, the control board is seeing resistance it doesn’t like. Sometimes that’s a bad safety sensor, sometimes it’s the board itself, sometimes the gate is dragging because of a hinge problem. The gate needs to be checked before the motor is blamed.
- The gate won’t move at all, but you hear clicking. A weak or dead battery is the classic Mighty Mule culprit here – the unit runs on a 12-volt battery charged by a small solar panel, and once the battery can’t hold a charge, the motor has nothing to push with.
- The arm swings but the gate doesn’t follow. The connection between the arm and the gate bracket has come loose, or the arm’s linkage has worn. On older units, the pivot pin and bushing wear faster than the arm itself.
- The gate won’t stop when something’s in the way. This one is a safety concern, not an inconvenience. If your safety sensors or the motor’s built-in obstacle detection aren’t working, treat the gate as unusable until it’s inspected.
One more thing worth saying plainly. When we’re called to a North Las Vegas address about a Mighty Mule that “keeps failing,” we often find the arm was fine and the hinge post was sagging. A gate that’s out of plumb puts resistance on the arm every single open cycle – and that’s what kills motors. We check the gate first. Every time.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what most Mighty Mule replacement jobs run in North Las Vegas, installed, quoted in writing before anything starts.
| Job | Typical Installed Range |
|---|---|
| Single-arm Mighty Mule replacement (unit + labor) | $575 – $850 |
| Dual-arm Mighty Mule replacement (pair + labor) | $850 – $1,150 |
| Control board replacement (unit kept) | $185 – $325 |
| Battery and solar charge check/replace | $85 – $165 |
| Safety sensor / sensor harness service | $95 – $215 |
| Gate alignment, hinge work, and bracket repair (added when needed) | $110 – $275 |
What drives the range: model, single versus dual, whether your existing wiring and sensor harness are reusable, and whether the gate itself needs attention before a new motor goes on. The gate alignment line is not padding – we’d rather fix the cause than watch a fresh arm fail in eight months. Every installation carries the 90-Day Done Right Promise, stamped in writing on your invoice. If something’s not right, one call brings us back, no runaround and no haggling about whose fault it was.
Standing offers apply: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. None of that requires asking for it.
DIY or Call Us?
Some checking is worth doing yourself before you call. You can read the model sticker, sweep the gate by hand to feel if it binds or drags, look for a cracked battery case or corroded terminals, and confirm the safety sensor LED comes on when you pass your hand through the beam. That information is genuinely useful and it’ll shorten your service call.
On the motor replacement itself, there’s a real safety caveat, and I’d rather say it once than have somebody get hurt. If your Mighty Mule unit is mounted to a gate with high-tension tension springs or a torsion assembly, that hardware is under stored energy. A tension spring that goes during a DIY swap can cause serious injury. The gate also weighs more than most people expect, and a gate that falls off a bracket mid-job is a heavy fall. And the electrical work – low-voltage at the arm, but still tied to a charger and a control board – shouldn’t be improvised. We’re insured and bonded, we’ve done this a few thousand times, and the cost of doing it once with us is usually lower than doing it twice.
If you’re ready to hand it off, call (844) 761-9351. We answer in our own voice, around the clock.
Frequently Asked Questions
Expect eight to twelve years for a residential Mighty Mule arm in North Las Vegas, but the desert climate shortens that. The 100-plus-degree summers cook batteries and control boards faster than most owners realize, and UV cracks the plastic arm housings we see on units older than about seven years. A gate that’s out of alignment can cut lifespan in half – it’s the second motor owner’s most common complaint, and it’s the one we prevent by checking the gate first.
Often, yes – and we’ll tell you when that’s the smarter call. If only the control board or battery has failed, repair makes sense and it’s a much smaller job. If the arm’s internal gear is stripped, or the housing is cracked, or your unit is old enough that the exact board is no longer available, replacement is usually more honest. We don’t swap parts that don’t need swapping, and we’ll tell you which camp you’re in before we charge you anything.
A single-arm replacement is typically a two to three hour job from arrival to test cycle. Dual-arm setups run closer to four hours. If your gate needs alignment work or the bracket is failing, add an hour. We’ll give you the window when you book, and we keep it.
We match your model to the correct Mighty Mule arm, board, or battery and order it, then install. You’ll see the part and the labor broken out separately on your written estimate. We don’t claim to keep every Mighty Mule part on hand – no honest gate shop does – but we’ll tell you the lead time before you commit. If the exact part is discontinued, we’ll give you the closest equivalent and its price in writing.
One last note on who we are. Gatewood Fence & Gate North Las Vegas is an independent gate specialist – we’re not affiliated with Mighty Mule. We service Mighty Mule alongside LiftMaster, Ghost Controls, DoorKing, and other major brands, and we’ve been at this locally since 2001. If you want to see the shop and shake a hand, the address is published. Hal will be there.
Call (844) 761-9351 for a free estimate on your Mighty Mule gate motor replacement in North Las Vegas. We answer around the clock, price upfront, and stand behind the work. That’s the whole pitch.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.