Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Access Control Installation: The North Las Vegas Owner’s Guide
Mighty Mule-compatible access control installation in North Las Vegas typically runs $375 to $850 installed, depending on whether you’re adding a keypad and entry/exit controls to an existing opener or replacing failed control components. We can often handle keypad and controller swaps the same day; full access-control builds get a free on-site measure and a written price first. Most owners discover the failure the same way: the keypad stops taking the code, or the gate stops responding to the remote and only opens with the manual release. Then the guessing starts, and that’s usually when we get the call.
Which Mighty Mule Models This Applies To
Mighty Mule access control splits into two families, and the split matters more than the brand name on the box. The older Mighty Mule and GTO/PRO lineage (the 350, 500, 502, and MM-series swing openers) used wired keypads and separate receiver boards, and those boards vary by revision – a keypad that belongs on a 500 will physically plug into a 502 and still not work, because the control board firmware reads it differently. The newer Mighty Mule lines moved to wireless keypads and integrated receivers, with different pairing steps per generation. To identify what you have, read the model plate on the opener housing (usually under the cover on the control arm), note the revision letter if it’s stamped there, and photograph the existing keypad’s wiring harness before anything comes off.
On the OEM-versus-aftermarket question: Mighty Mule replacement keypads and receivers from the manufacturer cost more and fit exactly once. Quality aftermarket equivalents for the older wired systems are widely available and often better sealed against dust, which matters in North Las Vegas. We install both. We don’t claim to stock parts or carry them on a truck – we source the right one for your revision and bring it to the job. We also service LiftMaster, Ghost Controls, and DoorKing access control, though this page sticks to Mighty Mule.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Access Control Installation Is Failing
- The keypad accepts the code but the gate doesn’t move. That’s usually the receiver board or the pairing between keypad and control board, not the keypad itself. Replacing the keypad alone is the most common wrong fix we get called out to correct.
- The gate opens on the remote but not on the keypad. This points to the keypad’s power or data line, or a wiring connection that loosened where the cable enters the housing. In North Las Vegas, sun-cracked cable jackets at that entry point are a regular find.
- Intermittent response that gets worse in the afternoon. Heat-related board faults show up this way – the control board works in the morning and quits above about 105°F. That’s a component failing, not a ghost.
- The gate opens by itself, or the keypad stops responding after rain and dust. Water and grit intrusion into the housing, often because the seal aged out or the cover wasn’t seated right at the last service visit.
- Exit loop or vehicle sensor never releases the gate. Loop detector or sensor failure, or a detector that was never set correctly for your driveway width. We test the detector with a meter before condemning it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in North Las Vegas ranges from about $375 to $850 for Mighty Mule-compatible access control work. The low end covers a keypad swap or a receiver replacement on an existing opener with good wiring. Mid-range covers keypad plus receiver plus re-terminating the entry cable. The high end covers adding entry and exit controls where none existed, including the exit loop or sensor and the low-voltage run to it.
| What’s involved | Installed range |
|---|---|
| Keypad replacement or repair, existing wiring | $375 – $475 |
| Keypad plus receiver/control board replacement | $475 – $650 |
| Adding entry and exit controls with loop or sensor | $650 – $850 |
| Re-running damaged low-voltage entry cable | Quoted on site |
We quote the price and you agree to it before any work starts. That price doesn’t move at the door. Every access control job carries the 90-Day Done Right Promise in writing – if it’s not right, one call brings us back. And if the part turns out to be repairable, the $40 off any repair over $200 standing offer applies, as does the permanent 10% discount for seniors and veterans.
DIY or Call Us?
You can safely do a few things yourself. Read the model and revision off the opener plate. Look at where the keypad cable enters the housing and check for cracked jacket or corrosion. Test whether the gate opens from the remote (which tells you the opener is fine and the problem is in access control). Beyond that, wiring a keypad into a live opener control board is low-voltage but unforgiving: misland a conductor and you can fry the board or leave the gate in a state that closes on a vehicle. We don’t hand out step-by-step wiring instructions, because the variations between Mighty Mule revisions mean the wrong step costs you a board. Call (844) 761-9351 and we’ll tell you what to check over the phone, then come out if it needs hands.
FAQs
Expect 5 to 8 years out of a keypad and 7 to 10 out of a receiver board here. The North Las Vegas sun and summer heat shorten that – units on a west-facing post take the worst of it, and we see sealed housings fail sooner when the seal ages out and wind-driven dust gets in.
Often, yes. Loose terminations, corroded connectors, a cracked cable jacket, or a keypad that just needs re-pairing with the board account for a lot of what we find. We test before we replace, which is why a second opinion on a written estimate is free – if someone told you the whole system is shot, let us look at it.
A keypad or receiver swap is typically 45 minutes to 2 hours, and many of those we handle same day. Adding entry and exit controls with a loop or sensor takes longer and is scheduled after a free on-site measure, because the cable run and driveway surface dictate the work.
By your model and revision, not just the brand name. We match the keypad or receiver to what’s actually on your opener housing, then bring it to the job. We don’t claim to stock Mighty Mule parts – we don’t claim stock of any part – and we’re an independent service provider, not affiliated with Mighty Mule.
If your keypad quit and you’re tired of guessing which board to buy, call (844) 761-9351. A live person answers around the clock, we’ll figure out your model together, and we’ll give you a straight written price before anything starts. Same number gets you the shop if you’d rather come look us in the eye.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.