A Gatewood company - serving North Las Vegas, NV

Mighty Mule Hinge & Roller Replacement in North Las Vegas, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Mighty Mule Hinge & Roller Replacement: The North Las Vegas Owner’s Guide

We replace Mighty Mule hinges and rollers in North Las Vegas for a typical installed cost of $240 to $420, and most single-gate hardware jobs are done in a single visit. The hinge is the bracket bolted to the gate post that lets the gate swing; the rollers are the wheels that carry the gate along its track on sliding models. Both wear out, and both fail in ways you can usually hear before you can see.

Call (844) 761-9351

Owners typically find out when the gate starts to drag, or when it stops latching the way it used to, or when a helper has to lift it to close. In older North Las Vegas neighborhoods, the tell is often a few inches of sag at the post. On sliding gates, it is usually a grinding note as the rollers pass over a worn section of track. Either way, the part that failed is not always the part you first suspect, which is why we look before we quote.

We are certified to service nine major gate brands, including Mighty Mule. We also service LiftMaster, Ghost Controls, and DoorKing. Gatewood Fence & Gate North Las Vegas is an independent service provider and is not affiliated with Mighty Mule.

Which Mighty Mule Models This Applies To

Mighty Mule has made gate operators in several families over the years: the long-running DIY swing openers (MM360 and similar), the slide models, and the newer solar-friendly lines. In this part of the valley we see mostly the swing models on driveways, with the occasional slide gate on a side yard. The hinges and rollers themselves are not model-locked the way an opener board is, but the mounting pattern and bolt sizing are specific to the gate and post, not just the opener.

That is the compatibility gotcha most DIY buyers hit: they buy a “Mighty Mule hinge” online expecting a drop-in, then discover the bolt spacing on their post does not match. The hinge bracket has to match the post that is actually there. Bring us the old part or a photo with a tape measure in it, and we can identify what you have. The machine label on the opener arm will tell us the model line.

On the OEM-versus-aftermarket question, we lean toward quality aftermarket hinges and rollers for two reasons. The metallurgy holds up well in desert heat, and the price is often half of a dealer-direct OEM part. We do carry OEM where the gate or post calls for it. We do not stock parts and we do not carry a parts truck. We source what your gate needs and bring it to the job.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Mighty Mule Hinge & Roller Replacement Is Failing

If any of these are familiar, the hardware is telling you it is done:

  • The gate sags at the hinge post. Hinge brackets bend or wear at the pin, so the gate loses its vertical hold at the post, not in the middle of the gate. If the sag is right at the post, the hinge is the suspect.
  • The gate drags or scrapes going closed. A worn roller has lost its round profile, or the bearing inside it has locked up, so the wheel slides instead of rolls. The gate scrapes the track or the ground.
  • Grinding or squealing as the gate moves. That is usually a worn roller bearing or a hinge pin that has lost its lubrication. In North Las Vegas, dust and heat accelerate both.
  • The gate will not stay latched. A failing hinge lets the gate rack out of square so the latch no longer lines up. The latch gets blamed; the hinge is usually the cause.
  • Visible rust, cracks, or loose bolts at the hardware. We see cracked hinge brackets and loose bolts on gates that have been in service well past the expected hardware life. Cracks mean replace, not tighten.

Replacement Cost & What’s Included

Installed pricing at Gatewood Fence & Gate North Las Vegas runs $240 to $420 for a standard single-gate hinge and roller replacement. That is a range, not a bait-and-switch, and the exact number is quoted and agreed before anyone touches the gate.

The range moves for a few reasons:

  • Number and type of hinges. A single swing gate typically has two or three hinges. Heavy steel gates take heavier hinge hardware than a light aluminum frame.
  • Roller count and track condition. A slide gate can have two to four rollers on each carriage. If the track is worn or bent, the new rollers may not run true until the track is addressed.
  • Post condition. A hinge is only as good as the post it bolts to. If the hinge post is loose, rotted, or cracked, the hardware replacement has to be quoted with that in mind.

Parts and labor are broken out rather than bundled, so you can see what you are paying for. Every job carries our 90-Day Done Right Promise in writing. If something we did is not right, one call brings us back.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

DIY or Call Us?

You can safely inspect your own hardware. Look for visible rust, cracks, and loose bolts. Check whether the gate sags at the post. Look at whether the rollers are round, or flat, or frozen. If you can measure the bolt spacing on the hinge and the diameter of the roller, write those down. That is all useful when you call.

Where DIY goes wrong is at the swap itself. A swing gate on a Mighty Mule operator weighs more than a single person can safely hold, the springs or arms store energy, and the gate will move when you take the last bolt out. Without a way to block the gate safely, the gate can fall. Our technicians have up to 25 years of experience and carry the blocking and the tools to do the job without a trip to urgent care.

Call (844) 761-9351 and we will talk through what you are seeing. A live person answers around the clock, and the estimate is free.

FAQs

Need your Mighty Mule hinges or rollers handled in North Las Vegas?

Call Gatewood Fence & Gate North Las Vegas at (844) 761-9351 for a free estimate. A live person answers 24 hours a day, seven days a week. If you have a failing hinge or a roller that has quit rolling, we will be there. Our technicians have up to 25 years of experience, and every job carries the 90-Day Done Right Promise in writing.

Standing offers? We have them. $40 off any repair over $200. No trip charge inside the county. A free second opinion on any written estimate. And a permanent 10 percent discount for seniors and veterans. No haggling required. Ask for the discount when you call.

Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (844) 761-9351
Local Service Coverage

Request a Free Estimate in North Las Vegas

Tell us what you need - Gatewood Fence & Gate North Las Vegas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch