Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Welding & Fabrication: The North Las Vegas Owner’s Guide
Welding and fabrication on a Mighty Mule gate in North Las Vegas usually runs $285 to $650 when a bracket, hinge or post weld has cracked or torn, and most of that work we finish in a single visit because it happens on site. We don’t haul your gate off – the repair happens in your driveway, on your post, with your gate staying where it lives. Most owners don’t go looking for welding work. They find it after a gate starts sagging on one side, or a hinge tears loose from the post, or an operator bracket rips off the frame and the arm goes slack. That’s the moment the phone rings.
Key Takeaways
- Mighty Mule gate steel and mounting failures are common in North Las Vegas heat, and most are repaired on site.
- Typical welded repair runs $285 to $650 installed, including materials and cleanup.
- We’re an independent gate service, not affiliated with Mighty Mule.
- Every welding job is backed by the 90-Day Done Right Promise, in writing.
Which Mighty Mule Models This Applies To
Welding and fabrication touch every Mighty Mule swing and slide gate line, because the steel and the mountings are what the operator bolts to. That means the MM260, MM360, MM560, MM572, the MMS100 slide series, and the heavier GTO-derived arms all put stress on the same points: the hinge post, the operator mounting bracket, and the gate frame where the arm connects. The model number doesn’t change the weld repair – it changes the bracket geometry and the pull force the steel has to survive.
To identify what you’re working with, look for the data plate on the operator housing (usually a sticker on the control box cover), and measure your gate leaf width and weight. Mighty Mule rates its operators by gate weight and length, and a bracket sized for a 250-lb leaf will fail fast on a 400-lb leaf. That’s the compatibility gotcha most homeowners miss: the operator may be correct, but the mounting was never matched to the gate.
On OEM versus aftermarket: Mighty Mule sells replacement brackets and hardware, and for structural welding we fabricate to match the original spec rather than force a universal part. If a factory bracket exists and fits, we use it. If it doesn’t, we build one. We don’t claim to stock parts – we source or fabricate what the job needs. We also service LiftMaster, Ghost Controls and DoorKing gates, so we see how the mounting hardware compares across brands.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Welding & Fabrication Is Failing
- Gate sags on the hinge side. The hinge post weld or the post itself has cracked or pulled. A gate sags in the hinge post, not in the middle – and that’s where we start looking.
- Operator arm pulls loose from the gate frame. The mounting bracket weld has fatigued. In North Las Vegas, summer metal expansion and daily cycles work that weld until it gives.
- Visible crack or rust line at a weld joint. Cracks start small and travel. A rust bloom at a weld means moisture has been getting in, and the joint is already compromised.
- Gate drags or binds when opening. A bent frame or a shifted hinge geometry throws the gate out of square, and the operator fights it every cycle.
- Operator strains or faults out mid-travel. The gate steel is out of alignment and the operator is working against it. Left alone, that kills the motor next.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Welded repair and fabrication in North Las Vegas generally lands between $285 and $650 installed. A straightforward hinge or bracket re-weld sits at the low end. A cracked post, a fabricated replacement bracket, a bent frame straightened and re-welded, or a gate pulled back into square pushes toward the top. What drives the number is access to the weld, how much steel has to be cut out and replaced, and whether rust or prior sloppy work has to be undone first.
The price we quote is the price you pay. We quote and agree on it before any work starts, and there’s no surprise at the door. Labor and materials are broken out, the weld is cleaned and treated, and every job carries the 90-Day Done Right Promise in writing. We also take $40 off any repair over $200, and there’s no trip charge inside the county.
DIY or Call Us?
You can safely check a few things yourself: look for cracks and rust at the welds, check whether the gate hangs square, and confirm the operator bracket bolts are tight. What you should not do is attempt structural welding on a gate that’s under spring or operator tension. A gate frame holds stored energy, and cutting or welding on a loaded member can release it suddenly. Beyond the safety side, a weld that isn’t properly penetrated fails again in months – we’ve re-done plenty of driveway welds that looked fine and let go. If you’re not sure, call (844) 761-9351 and we’ll tell you straight.
FAQs
How long does a welded gate repair last in North Las Vegas? A properly executed weld on clean steel lasts years, often the life of the gate. North Las Vegas heat and UV are hard on paint and coatings, so the key is treating the weld afterward – bare steel rusts fast here. We prep and coat every weld we make.
Can my gate be repaired instead of replaced? Almost always, yes. Cracks, torn brackets and bent frames are repairable. Fix the panel without the post and you’ll fix it twice, which is why we check the post first. Replacement is the last resort, not the first.
How long does the weld repair take? Most welded repairs are done in a single visit, often within a couple of hours. Fabricated brackets and bent frames may run longer depending on what we find once the gate is opened up.
How do you source the part? We measure the original bracket or weld point, match it to the Mighty Mule series, and either source the factory part or fabricate a replacement to spec. We’re an independent gate service and not affiliated with Mighty Mule – we repair their equipment, we don’t represent the brand.
Call (844) 761-9351 for a free estimate. A live person answers around the clock, and we’ll give you a straight answer on what your gate needs.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.