Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Hinge & Roller Replacement: The North Las Vegas Owner’s Guide
We replace failed Linear hinges and rollers on sliding gate systems in North Las Vegas, and most jobs run $180 to $420 installed depending on how many hinges and rollers are shot and whether the track has worn with them. If your gate is dragging or hanging crooked right now, call (844) 761-9351 and we’ll get you a straight answer the same day. Linear is one of the nine major brands we’re certified to service, right alongside LiftMaster, Mighty Mule, and Ghost Controls.
Here’s how North Las Vegas owners usually find us. The gate starts catching halfway through its slide, or it grinds going one direction and glides the other. Sometimes it’s simpler: the gate stops closing square and you can see daylight under one end. By the time it catches, the roller on that side has usually been flat for a while. A roller doesn’t announce itself. It wears quietly in the heat, and the hinge takes the abuse until the gate starts riding on its own weight.
Key Takeaways
- Installed hinge and roller replacement on a Linear sliding gate typically runs $180 to $420 in the North Las Vegas area.
- We bring the part to the gate. You don’t haul anything to the shop.
- Left alone, a worn roller puts stress on the operator and the gate frame, and that’s where repair costs climb fast.
- Every replacement job carries our 90-Day Done Right Promise in writing.
- A live person answers the phone any hour, any day. No voicemail, no queue.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Which Linear Models This Applies To
Linear’s sliding gate hardware spans several series lines, and the hinge and roller assemblies aren’t universal across all of them. The tracked gate operators and the slide-gate roller systems use different roller diameters, different shaft lengths, and different hinge bolt patterns. If you’re ordering parts yourself and you skip the model check, you can end up with a roller that looks right in the box and won’t seat in the bracket.
Here’s the compatibility gotcha that bites do-it-yourselfers most often: the roller wheel diameter and the shaft shoulder size have to match the bracket channel, not just the bolt hole. A 1/16-inch difference in shoulder length is enough to leave the roller riding on the shoulder instead of the wheel face, and it will wear through in weeks. The model plate on your Linear operator will give you the series reference. If you can’t find it, the bracket itself is usually stamped or cast with the size.
On the OEM-versus-aftermarket question: Linear’s own hardware is built for the model, and it fits without question. Quality aftermarket equivalents can hold up well if the steel is the right grade and the bearing is sealed the way the original was. What we won’t do is hand you a hardware-store roller sized “close enough.” On a gate that slides every day, close enough fails inside a year. We source the right part for your Linear unit, and we tell you plain when aftermarket is fine and when you should stick with OEM.
One note on who we are: Gatewood Fence & Gate North Las Vegas is an independent service provider. We repair and service Linear equipment, but we’re not affiliated with Linear and we don’t speak for the manufacturer.
Signs Your Linear Hinge & Roller Replacement Is Failing
Rollers and hinges wear out from friction and weight, and North Las Vegas summers speed that up. Heat softens the bearing grease and the dust grinds it into paste. You’ll see the failure coming if you know what to look for:
- The gate drags or jerks through the middle of its travel. A roller that’s lost its round profile intermittently binds, and the operator fights it at the same spot every time.
- The gate rides out of square, with one end low. A collapsed roller or a hinge that’s pulled loose from the post lets that corner sag. The gate isn’t the problem; the hardware holding it has given up.
- You hear a grinding, squealing, or clicking sound. That’s metal on metal where there used to be bearing. Once it’s grinding, the roller is past saving and probably damaging the track too.
- The gate wobbles side to side when it’s stopped. A worn hinge pin or a bent hinge strap makes the gate lean. Left alone, that wobble rattles the posts and the operator arm.
- Visible flat spots, cracks, or rust weeping from the roller. Flat spotting comes from sitting loaded in one position. Rust and cracks mean the wheel is failing structurally, and it can come apart while the gate is moving.
By the time you’re hearing metal on metal, the gate has usually been telling you for a while. Fix the panel without the post, as the saying goes, and you’ll fix it twice. That’s why we check the hinge post and the track at the same time we look at the rollers. If it needs welding, we do it on site, in your driveway. The gate doesn’t leave.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what you’ll actually pay in North Las Vegas, parts and labor together:
| What you’re getting | Typical installed range |
|---|---|
| One roller replaced (part plus labor) | $180 – $240 |
| Both rollers and one hinge | $240 – $340 |
| Full set: all rollers plus hinges on a standard sliding gate | $320 – $420 |
| Track realignment or on-site weld on a pulled hinge post | Add $75 – $160 |
What moves you up or down that range is how many parts have actually failed and whether the track and post are still sound. A single bad roller on a sound track is the bottom of the range. A gate that’s been dragging long enough to flatten every roller and wear the track is the top, and sometimes welding is needed to bring the post back true.
The price we quote is the price you pay. We give you a written number before we pick up a tool, and it doesn’t change at the door. If we get in there and find something we didn’t see on the walk-through, we stop and tell you what it costs before we touch it. You’re never handed a surprise. We also take $40 off any repair over $200, there’s no trip charge inside the county, and seniors and veterans get a standing 10% off. If you have a written estimate from somebody else, we’ll give you a free second opinion on it. Every repair we do is backed by the 90-Day Done Right Promise, stamped in writing. If it’s not done right, one call brings us back and we make it right.
DIY or Call Us?
Some of this you can check safely. If your gate is electric, cut the power at the disconnect first, then look. You can walk the gate by hand and feel for the catch. You can watch the rollers track as you push it slowly. You can eyeball the hinge straps for a gap or a rusted pin. That much is safe and it tells you where the problem lives.
Where it goes wrong is the repair itself. A sliding gate carries several hundred pounds, even a small one, and the moment you pull a hinge pin or unbolt a roller, that weight has to go somewhere. We’ve seen gates dropped on feet, hinge posts bent past saving, and pinch points catch fingers because the gate wasn’t blocked. Gate operators can move with stored force, too. This isn’t a scare tactic, it’s just what the weight does. We bring the blocking, the right hardware, and the welding rig. If the post needs straightening, we fix it on site so the gate never comes off its track. Call (844) 761-9351 and we’ll come look. The estimate is free.
FAQs
Sealed rollers and quality hinges usually give you five to eight years here, and less if the gate runs tight against its track or the operator over-drives it. The North Las Vegas heat and dust work against any bearing. Grease thins out in summer and blows into grit that grinds away the bearing surface. Rollers on the sunny side of a gate often wear faster than the shaded side for exactly that reason. If we replace them as a set and you keep the track clean, you’ll get a long run out of them. Call (844) 761-9351 for a quote on your Linear gate.
Sometimes, but a worn roller can’t be rescued once it’s lost its round profile or the bearing is gone, and a hinge with a stretched pin shouldn’t be re-pinned. Where it makes sense, we do repair rather than replace. A hinge that’s just worked loose from the post gets re-bolted and welded, which is far less than new hardware. A roller with a damaged seal gets swapped. A hinge strap that’s bent but sound gets straightened. We look first and tell you what’s actually needed. If replacement is the honest answer, we’ll say so. Estimates are free, so call (844) 761-9351.
A standard roller and hinge set on a Linear sliding gate usually takes one to two hours once we’re on site, and we can often get to you the same day if you call in the morning. If a hinge post needs welding or the track has to be re-set, plan on closer to half a day. We don’t leave until the gate slides clean, closes true, and the operator cycles right. You’ll see it work before we go.
We match the part to your model and the actual bracket dimensions, measured on the gate, not just to what the label says. We bring the hardware with us so there’s no return trip waiting on an order. What we won’t do is guess a size. If a part is special-order, we tell you the wait and the price upfront, and you decide before we order anything.
If your Linear gate is dragging, grinding, or hanging out of square, don’t wait for it to quit working. Call (844) 761-9351 for a free estimate. A live person answers around the clock, and we’ll get out there and tell you straight what it needs.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.