Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Welding & Fabrication: The North Las Vegas Owner’s Guide
Welding and fabrication on a Linear gate comes down to the steel, not the electronics. In North Las Vegas, most Linear gate repairs that need a torch fall into a $250 to $650 range for the welding itself, plus parts if hinges, brackets, or a roller carriage have to be replaced. We’re set up for on-site work, so for a gate that’s sagging, dragging, or rattling in its track, we can often get out the same day and fix it where it stands.
Owners usually find out they have a fabrication problem the same way. The gate starts catching on the ground when it rolls back. Or a hinge post looks a little crooked after a monsoon-season gust, and the next week the whole gate won’t latch. Sometimes it’s a weld that cracked at a corner seam after twenty years of heat cycles and dry air. A Linear operator can be perfectly healthy and the gate still won’t run right, because the steel it’s pushing against has given up. That’s a fabrication job, and it’s the kind of thing we handle on site instead of hauling the gate away.
Which Linear Models This Applies To
Linear swing and slide gate operators show up on a lot of residential driveways around North Las Vegas, and the welding and fabrication needs cross most of the line. The common Linear swing operators (the LSO and similar residential swing units) hang off hinge posts and mounting brackets that take real stress every time the gate moves. Slide operators (the LS-series and comparable) ride on a track and carriage assembly, and that track wears and the steel around it fatigues. Fabrication work on either type is about the gate structure the operator is bolted to, not the operator box itself.
The way to get the right repair is to identify two things: the operator model on the housing label, and the actual gate dimensions and post condition. Model numbers on Linear units are usually printed on a sticker inside or under the housing cover, and the gate hardware (hinges, brackets, carriage) is what we measure. On OEM versus aftermarket: for structural steel and welding, there’s no OEM-vs-aftermarket question, because we’re fabricating the bracket or repairing the weld to match what’s there. For any factory Linear component involved, we’ll tell you plainly whether an OEM replacement makes sense or a quality equivalent does the same job for less. We know these operators, but we’re an independent service provider, not affiliated with Linear.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Linear Welding & Fabrication Is Failing
A gate sags in the hinge post, not in the middle, and that’s where we start looking. Here’s what owners report before they call us:
- The gate drags or scrapes the ground on the swing or slide. That usually means the hinge post has shifted or the carriage has worn, and the gate is riding lower than it should. Left alone, the operator fights the drag and the motor pays for it.
- A visible crack at a weld seam or corner joint. Decades of North Las Vegas heat cycling, dry air, and the occasional hard wind load work on those joints. A hairline crack at a corner is the classic sign the steel is fatiguing.
- The gate won’t latch or lines up crooked when closed. That’s a post-and-frame alignment problem, not an operator problem. Fix the panel without the post and you’ll fix it twice.
- The operator strains, reverses, or stops mid-travel. When the steel binds, the Linear operator reads that resistance as an obstruction and backs off or stalls. The operator is telling you the gate is fighting it.
- Loosened bolts, a rocking hinge, or a bracket pulling away from the post. Fasteners work loose when the steel underneath is moving. A bracket that rocks is a fabrication repair waiting to happen.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Welding and fabrication repairs in North Las Vegas generally run $250 to $650 installed, depending on what’s involved. A single cracked seam or a re-welded hinge bracket sits at the low end. A bent or failed hinge post, a new roller carriage, or rebuilding a bracket that’s pulled loose from concrete pushes toward the top. A full gate section repair with new steel can go higher, and we’ll say so before we start.
What drives the range: how much steel has to be cut out and replaced, whether the post has to be reset, and how accessible the work is. The fabrication labor and any parts are quoted together as one number, so you’re not watching a meter run. Every job carries the 90-Day Done Right Promise in writing, and the price we agree on before work starts is the price on the invoice. Standing offers apply too: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (844) 761-9351 for a free estimate.
DIY or Call Us?
Some things you can safely check yourself. Look at the post for movement or rot at the base. Eyeball the gate for a sag or a gap that’s opened at a corner. Check that bolts are tight and the track is clear of debris. Those observations help us quote faster over the phone.
Where DIY goes wrong is the welding itself. Gate frames and hinge posts carry real load, and a weld that looks fine but lacks penetration will crack under the weight and the wind. There’s also the heat and fire risk of welding near dry brush, and the safety hazard of a gate that could drop or swing unexpectedly while you’re underneath it. This is the part where a trained hand matters. If your Linear gate is dragging, cracking, or won’t line up, call (844) 761-9351 and we’ll take a look. The estimate is free, and we’ll tell you straight whether it’s a weld, a post, or something simpler.
FAQs
A proper weld on a sound frame generally holds for many years, and the steel around it is usually what ages first. What shortens the life of a repair is an underlying problem that wasn’t addressed, like a loose post or a failing carriage that keeps stressing the joint. We fix the cause, not just the crack, so the repair lasts.
Usually, yes. Most Linear gate fabrication problems are a cracked weld, a worn bracket, or a post that needs resetting, and those are repairable on site. Replacement is the answer when the frame itself is rusted through or bent beyond straightening. We’ll tell you which you’re looking at, honestly, before any work starts.
A single weld repair or bracket replacement is often a same-day job, sometimes within a couple of hours on site. A post reset or a larger frame repair can take longer, and we’ll give you a realistic window when we quote. We don’t haul the gate off, so the work happens in your driveway where the gate belongs.
Structural steel and weld repairs are fabricated to match your gate, so there’s no factory part to chase. For any factory Linear component involved, we identify your model from the label and source the correct replacement or a quality equivalent we trust. We don’t claim to stock parts, but we’ll get the right one and tell you the honest price. Call (844) 761-9351 for an exact quote.
Written by the team at Gatewood Fence & Gate North Las Vegas, serving North Las Vegas and nearby areas.