Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Sunrise Manor
If your gate is dragging, sagging, or the latch won’t line up anymore, we fix it here in Sunrise Manor – not by hauling it off, but with on-site welding and real parts. Our technicians have up to 25 years of experience, and they work on gates hung in block piers and welded to the wall every single week in this township. Call (844) 761-9351 and a live person picks up, day or night. We quote the price before we touch a thing.
Why Gatewood Fence & Gate North Las Vegas Is Sunrise Manor’s Preferred Gate Parts & Welding Company
Sunrise Manor is where we do a lot of the work we’re proudest of, and folks here know us for it. When a gate hangs from a block pier that’s pulled away from the wall, we re-set and re-anchor the pillar and re-weld the hinge straps – we don’t sell a whole new gate around the problem. Every job comes with the 90-Day Done Right Promise in writing, so if something’s off, one call brings us back.
We answer the phone around the clock with a live person – not a voicemail, not a call center. A repair over $200 gets $40 off, there’s no trip charge inside the county, and seniors and veterans keep a permanent 10% discount. We’ll give you a free second opinion on any written estimate somebody else handed you.
Most jobs in Sunrise Manor run on-site welding, which means the gate stays in your driveway where it belongs. We know the streets, the block walls, and how the caliche soil moves here. That matters more than any sales pitch.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Sunrise Manor
Whether you drive through Sunrise Manor off Charleston or Bonanza, your gate is probably fighting the same three things: rusted hinges, cracked piers, and monsoon-wrecked alignment. Here’s how we handle each piece. For the full picture of what we do, see our Gate Parts & Welding hub.
Hinge Replacement in Sunrise Manor
Original welded-steel hinges rust and seize here after enough 100°F-plus summers, and when they do, the gate sags at the hinge post rather than the panel. That’s where we start – cutting the old hinge, welding a fresh strap, and setting it square. A pair of hinge replacements typically runs $140-$260 in Sunrise Manor, set in the block pier so the swing lands true.

Post Replacement in Sunrise Manor
When the block gate pier has separated from the front wall, no amount of hinge work saves it. We re-set and re-anchor the pillar first, then bring the gate back to it. A post or pier re-anchor usually runs $350-$700 depending on how far the caliche soil has pushed things, and a rusted steel post replacement sits in the $300-$550 range.

Rail Repair in Sunrise Manor
Monsoon winds rack chain-link and steel swing gates, bending top rails and knocking latches clean out of the strike. We straighten and re-weld the rail on site, then reset alignment so the gate swings clean. Rail straightening and re-welding in Sunrise Manor typically runs $120-$300 per gate.

Custom Welding in Sunrise Manor
Sometimes the honest answer is a custom bracket, a reinforcement at the pier, or a new latch plate built to fit an older gate. We weld it in the driveway. Custom welding and fabrication on a residential gate generally runs $150-$400 in Sunrise Manor, quoted up front before we start.
We also handle gate rollers and latch and lock work – both common on side and driveway swing gates around ZIP code 89110.
Trusted Brands We Service in Sunrise Manor
We’re certified to service nine major gate brands, including Linear, Viking, DoorKing, and Ghost Controls, and that list covers most of what’s hanging on Sunrise Manor gates. When a brand-specific part is needed, we get it without dragging the job out for weeks, and we’ll tell you honestly whether a part swap is even the right call. No parts warehouse, no upsell – just the repair your gate actually needs, quoted before we begin.
Common Gate Parts & Welding Problems We See in Sunrise Manor Homes
- Block piers pulling away from the wall. The caliche-heavy soil here swells and shrinks with the seasons, and block gate piers routinely separate from the front wall as it does. That throws the whole swing gate out of alignment before a single hinge has failed.
- Rusted, seized hinges. Years of extreme Mojave heat seize the original welded-steel hinges, and the gate sags at the hinge post. Tightening a bolt won’t fix that – the hinge itself has to come off and a new one go on.
- Monsoon-rattled rails and latches. Seasonal monsoon winds rack chain-link and steel swing gates hard, bending rails and knocking latches out of the strike. Left alone, the gate racks further until it won’t close at all.
- Older chain-link side gates. Many Sunrise Manor homes still have the original welded-steel or chain-link side gates, and they’re often rusted at the hinge and hung off a settled pier. Repair usually beats replacement if the frame is still sound.
Here’s a typical Sunrise Manor lot: a welded-steel or chain-link driveway swing gate hangs from block piers that have separated slightly from the front wall as the caliche soil heaves, so the gate drags, the latch stops lining up, and the hinges have seized from years of 100°F-plus summers. A qualified local tech usually diagnoses the hinge post and pier anchoring before touching the panel – re-setting and re-anchoring the block pillar, then re-welding hinge straps and correcting the sag. Because monsoon winds rack the panels, alignment and latch strike get reset last so the gate swings clean.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Parts & Welding in Sunrise Manor, NV
Here’s what this work runs in Sunrise Manor, quoted clearly so you’re not guessing. Every price is agreed in writing before any work starts, and it doesn’t change at the door.
| Job | Typical Sunrise Manor Range |
|---|---|
| Hinge replacement (pair) | $140 – $260 |
| Post / block pier re-anchor | $350 – $700 |
| Steel post replacement | $300 – $550 |
| Rail straighten & re-weld | $120 – $300 |
| Custom welding & fabrication | $150 – $400 |
| Gate rollers (set) | $100 – $220 |
| Latch & lock replacement | $90 – $200 |
What moves the number is how far the pier has separated and whether we’re re-welding to existing steel or fabricating new. Estimates are free, and a repair over $200 comes with $40 off. Call (844) 761-9351 for an exact quote on your gate.
We Also Serve Cities Near Sunrise Manor
We do gate work across the east valley, including Whitney, Winchester, Las Vegas, and North Las Vegas. Same on-site welding, same Done Right Promise, same live person on the phone. If you’re just outside Sunrise Manor, we’ll still come look at your gate and quote it in writing. Reach out and we’ll get you scheduled.
Serving Sunrise Manor, NV – Our Local Coverage Area
We serve Sunrise Manor and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Sunrise Manor
No – and that’s one of the few genuinely local facts about doing gate work here. Because Sunrise Manor is an unincorporated Clark County township rather than a city or an HOA jurisdiction, there’s no municipal or association gate standard to approve your style, height, or finish against. What governs the job is your homeowner’s block-and-weld setup and how the caliche soil is moving under your piers. If you want to change a gate, we’ll talk through what actually holds up in the ground before we build it. Call (844) 761-9351 for a free estimate.
Because a gate sags in the hinge post, not in the hinge bolts, and tightening them does nothing once the post has moved. In Sunrise Manor, that’s almost always the block pier settling or pulling away from the wall as the caliche soil swells and shrinks. Fix the panel without the post and you’ll fix it twice. We diagnose the pier and hinge post first, then re-anchor and re-weld so it holds. Call (844) 761-9351 and we’ll take a look.
The operator is fine; the gate itself is binding. A seizing hinge, a dragging roller, or a sagging gate out of square makes the motor fight resistance it can’t overcome, and on our older Sunrise Manor swing gates it’s usually a seized hinge or a pier that’s moved. We check the hardware first before anyone touches the motor, because replacing an operator won’t fix a gate that’s fighting its own hinges. Call (844) 761-9351 for an honest look.
Yes – if your gate has a motor, entrapment protection is required, and we install and check it as part of any operator work. Photoelectric sensors and safety edges are what stop a gate on an obstruction, and a gate that closes on its own without them isn’t one we’ll leave running. We test the safety equipment as part of the job so it functions the way it should. Call (844) 761-9351 to have yours checked.
Usually yes, if the frame is still sound. Rust at the hinges is exactly the kind of thing we weld and re-hang in Sunrise Manor every week, and it’s cheaper than a new gate. We’ll tell you plainly if the steel is too far gone to save, but repair-first is how we work. Call (844) 761-9351 for a free second opinion on your gate.
Get Your Sunrise Manor Gate Fixed Right
If your gate is dragging, sagging, or rusted at the hinge, don’t wait for it to fail all the way. We answer the phone around the clock with a live person, quote the price before any work starts, and back every repair with the 90-Day Done Right Promise in writing. Seniors and veterans keep a permanent 10% discount, and there’s no trip charge inside the county. Call (844) 761-9351 for a free estimate on your gate in Sunrise Manor.
Written by the team at Gatewood Fence & Gate.