Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Boulder City
If a gate in Boulder City is sagging, dragging, or banging in the wind, we can get it back on track. We’re Gatewood Fence & Gate, and Boulder City is one of the towns we know best, from the historic district streets in 89005 out toward the dry edge of 89006. That matters here, because the gates in this town sit on dam-era masonry and posts driven into caliche-hard ground, and they take a beating from desert wind and sun. A gate that fails here usually needs re-anchoring and welding on site, not a part swap pulled off a shelf. Call (844) 761-9351 and a live person picks up, day or night.
Why Gatewood Fence & Gate North Las Vegas Is Boulder City’s Preferred Gate Parts & Welding Company
We’ve built a name in Boulder City the slow way, one hinge post and one stubborn old gate at a time. Folks here have been burned by outfits that quote one price on the phone and hand over a bigger invoice at the door, so we do it the other way: the price is quoted and agreed before any work starts, and it doesn’t move. Our technicians have up to 25 years of experience, and they show up when we said they would. Every job carries the 90-Day Done Right Promise in writing, so if something isn’t right, you make one call and we come back.
When a wind event rolls across the McCullough Range and a gate starts dragging, you don’t want a voicemail. You get a live person on the line around the clock. We also give a free second opinion on any written estimate, take $40 off any repair over $200, skip the trip charge inside the county, and keep a permanent 10% discount for seniors and veterans. Boulder City customers keep us around because the work holds up through the next dust storm.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Boulder City
Most of what we do in Boulder City falls into four buckets: fixing the hinge, fixing what the hinge is bolted to, repairing the rails, and welding a custom piece when nothing off the shelf fits. That last one comes up a lot in a town this old.
Hinge Replacement
A gate sags at the hinge post, not in the middle, and that’s where we start. On many Boulder City properties the hinge pin has wallowed out the old masonry, or the gate swings on hardware that hasn’t been touched since the dam crews hung it. We replace the hinge and make sure it’s solid on whatever it’s mounted to, so the sag doesn’t come back next season.

Post Replacement
When a post has loosened or rotted, a new hinge on top of it is wasted money. Fix the panel without the post and you’ll fix it twice. Getting a footing dug out of caliche here takes a rock bar and patience, and if the gate hangs on a dam-era masonry wall, re-anchoring with the right hardware into that old block is its own craft. We do it in your driveway, not in a shop miles away.

Rail Repair
Boulder City’s low humidity and hard UV dry out and split wood gate rails faster than people expect. We repair the rail, reinforce it, and check the frame around it. If the wood is too far gone, we can weld up a steel replacement that will shrug off the next round of wind.

Custom Welding
You can’t buy a hinge that fits a 1930s Bureau of Reclamation gate off a shelf. Our Gate Parts & Welding team welds custom brackets, braces and replacement parts on site, so an original gate stays original and keeps working. That’s the piece other outfits skip because they’d rather sell you a whole new gate.
Trusted Brands We Service in Boulder City
We’re certified to service nine major gate brands, and in Boulder City we see DoorKing and LiftMaster operators most, with the occasional Mighty Mule on a lighter driveway gate. When a part fails, we identify it, tell you straight what needs to happen, and get the right component ordered without a long wait. We don’t keep a warehouse of parts, so the turnaround depends on the part, but we’ll give you an honest window before we start.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Boulder City Homes
This is desert country at roughly 2,500 feet, with 100°F-plus summers, punishing UV, and wind that carries grit. That mix wears gates out faster than in milder climates, and the dam-era housing stock adds its own challenges. Here’s what we run into most:
- Sand-jammed tracks and rollers. Wind-driven sand abrades slide gate tracks and rollers until the gate binds, and then the operator motor starts to strain. Cleaning and re-aligning the track saves the motor.
- Freeze-thaw cracked welds. Occasional winter freezes crack welds on older iron gates and loosen masonry anchors in the dam-era walls. A hairline crack caught early is a cheap weld; ignored, it becomes a new frame.
- Sagging from shallow footings. High winds load up solid infill gates and fatigue hinge posts set shallow in caliche, and the gate starts to drag. Correcting the hinge post first is the fix that lasts.
- Dried, splintered wood rails. UV and low humidity dry and split wood gate rails, which then catch the wind. We repair or replace the rail, or weld a steel one in its place.
Pricing for Gate Parts & Welding in Boulder City, NV
Nobody likes a surprise at the door, so here’s what this work typically runs in Boulder City. A hinge replacement usually lands around $150 – $350 per hinge. Post replacement, because of the caliche digging and old-masonry re-anchoring, runs higher, roughly $300 – $900 depending on the post and footing. Rail repair comes in around $120 – $400, and custom welding or fabricated brackets usually run $150 – $500. What moves the number is whether we’re mounting to a modern post or re-anchoring into 1930s masonry, and whether a part has to be fabricated. We give you the price before any work starts, and it’s the price you pay. Call for a free estimate – a free second opinion on any written bid is always on the table.
We Also Serve Cities Near Boulder City
We handle gate work well beyond Boulder City. If you’re over in Henderson, Whitney, Paradise, or Enterprise, the same repair-first approach applies. For Gate Parts & Welding in Boulder City and the towns around it, you get the same on-site welding, the same live person answering the phone, and the same written promise on every job.
Serving Boulder City, NV – Our Local Coverage Area
We serve Boulder City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Boulder City
The ground and the housing stock are different. Boulder City’s historic district sits on caliche-hard desert, and many gates hang on masonry walls built by dam-era crews, so the hinge post or masonry anchor takes the load and fails first. Vegas lots are usually newer and built on looser, backfilled ground, so failures spread into the panel instead. Here the fix starts at the hinge post and works outward.
Every automatic gate operator has a manual release, and it lets you move the gate by hand when the power’s out. The key is to release it correctly and never force a gate that’s stuck. If you’re not sure how yours disengages, call us and we’ll walk you through it for your specific operator. Getting it wrong can damage the motor or, worse, let a heavy gate swing free.
Grinding, binding, or a gate that moves slower than it used to are the usual signs a dust storm has jammed the tracks and rollers. Listen for the motor straining and check whether the gate drags at any point in its travel. Those are the same symptoms that lead to a burned-out operator if they’re ignored, so it’s worth a look before the next wind event.
Yes. Original dam-era gates often need a bracket or hinge that isn’t sold anywhere, and we fabricate and weld it on site so the gate stays in place. That’s the whole point of on-site welding: your gate doesn’t get hauled off, and an original piece keeps working instead of being replaced.
Your operator should have working safety photocells and, where required, other entrapment protection, and UL 325 is the standard those features are built to. Have someone test the safety devices and confirm they stop or reverse the gate, and check that the operator’s manual release works. If you’re unsure whether your Boulder City gate meets it, have a qualified tech look at it – this is a safety matter and shouldn’t be guessed at.
When a Boulder City gate starts to sag or jam, the fastest way to sort it is a phone call. Reach us at (844) 761-9351 for a free estimate, talk to a live person any hour, and we’ll get your gate solid and swinging right again.
Written by the team at Gatewood Fence & Gate.