Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Parts & Welding for North Las Vegas Homeowners
If your driveway gate has started dragging, listing to one side, or popping loose at the hinge, the fix is almost always structural, not cosmetic. That sag is coming from the hinge post or the weld holding the frame together, and welding it in place is what keeps the gate where it belongs. Our technicians have up to 25 years of experience diagnosing exactly that kind of wear. We answer every call with a live person around the clock, and we offer same-day repairs across North Las Vegas when the schedule allows. Call (844) 761-9351 and we’ll tell you straight what’s wrong and what it takes to fix it.
What Our Gate Parts & Welding Service Includes
This isn’t a parts-swap operation. We look at what actually failed, repair the metal or the hardware that gave out, and weld on site so your gate never leaves the driveway. Here’s what the work covers.
Hinge Replacement
Hinges carry the full weight of the gate and take the beating every time it opens and closes. When a hinge wears flat or the barrel snaps, the gate droops and drags on the ground until it tears itself apart. We cut out the failed hinge, weld on a proper replacement, and realign so the gate swings true instead of fighting you.

Post Replacement
The hinge post takes the most load in any gate system, and it’s the piece that fails first when water gets into the base or the concrete footing shifts. A sagging gate is usually a post problem in disguise. When a post is too far gone to save, we replace it, reset the footing, and weld the frame back to a solid anchor point.

Rail Repair
Rails are the horizontal bars tying the frame together, and a cracked or rusted rail lets the whole gate flex and twist. Left alone, that flex breaks welds at the corners and spreads the damage. We repair or replace the rail and re-weld the joints so the frame holds its shape under its own weight again.

Custom Welding
Sometimes a gate needs a piece that was never made for it: a reinforcing gusset, a new top rail, a bracket for a motor, or a repair to a wrought-iron section that no catalog part will fit. We weld custom pieces on site, in your driveway, matched to the existing metal. You get a repair built for your gate rather than a generic part forced to fit.
Gate Rollers
Sliding gates ride on rollers, and worn rollers make the gate grind, jump the track, or stop halfway. Bad rollers also strain the operator motor, which is an expensive way to find out the rollers were shot. We replace worn rollers, check the track alignment, and confirm the gate rolls smoothly before calling it done.
Latch & Lock
A latch that won’t catch or a lock that won’t engage leaves your property open whether you realize it or not. We repair and replace latches, locks, and the hardware that keeps a gate closed and secure. If the gate is part of an access-control setup with a LiftMaster or Linear operator, we make sure the mechanical latch and the electronic release work together.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Parts & Welding
We work on the equipment North Las Vegas homeowners actually have. LiftMaster operators are common on residential driveways, and we know where their hardware mounts and how a bent bracket throws the whole gate off. FAAC and BFT systems show up on heavier swing gates, and we understand how their arms and hinges take load so our welding doesn’t fight the operator’s geometry.
Linear and Mighty Mule gate openers turn up on plenty of driveways too, and we’ve learned where the mechanical parts wear out first on each one. Whether your gate runs on LiftMaster, FAAC, BFT, Linear, or any other make, we can help.
Signs You Need Gate Parts & Welding Right Now
- Your gate sags or drags on the ground. A gate that sags in the middle is usually failing at the hinge post, and that’s where we start. Waiting lets the frame twist and turns a hinge repair into a full rebuild.
- You can see cracked paint or rust at a joint. Cracks at a weld or hinge point mean the metal is moving where it shouldn’t. It’s the earliest sign of a failing weld and the cheapest time to catch it.
- The gate won’t latch or swings open on its own. A gate that closes on its own is telling you the posts are out of plumb or a hinge has gone. It’s a security gap as much as a mechanical one.
- The gate wobbles when you push it. A wobble means loose hardware, a worn hinge, or a post pulling from its footing. Push-test the gate by hand and you’ll feel where the slack is before it fails.
- Rollers grind or the gate jumps the track. On a sliding gate, noise and jumping mean worn rollers or a misaligned track. Left alone, the operator motor takes the strain and that repair gets expensive fast.
Our Gate Parts & Welding Process – Step by Step
- 1
We look at the gate in person before quoting. We check the hinge post for plumb, feel the frame for flex, and look at the welds and hardware. No phone guess becomes a surprise invoice.
- 2
We explain what failed and why. You hear the diagnosis in plain terms, including what happens if it’s left alone, so you can make a real decision.
- 3
We give you an upfront price in writing. The price is quoted and agreed before any work starts. No haggling, no numbers that climb at the door.
- 4
We weld and repair on site. The gate stays in your driveway. We cut out the failed parts, weld in replacements, and check alignment as we go.
- 5
We test the gate with you and back it in writing. We cycle the gate, check the latch and rollers, and hand you the 90-Day Done Right Promise. If it’s not done right, one call brings us back.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in North Las Vegas?
Gate parts and welding in North Las Vegas typically runs $150 to $650 depending on what failed, and most single-part repairs land in the $200 to $400 range. A hinge replacement usually runs $150 to $300 per hinge depending on the gate’s weight. Post replacement is the bigger job at $350 to $650 because the footing and alignment have to be reset. Rail repair and custom welding fall around $200 to $500 depending on the length and type of metal. Roller and latch work is on the lower end, generally $120 to $250.
Several things move the number: the gate’s size and weight, whether it’s steel or wrought iron, how far gone the post is, and whether a motor is involved. Rusted or bent bolts, gates that have been patched before, and electric gates with access control all take more time. Our standing offers help: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Every free estimate includes the full diagnosis, the written price, and a clear explanation of what’s included. The price we quote is the price you pay.
Gate Parts & Welding Near North Las Vegas – Our Service Area
We serve North Las Vegas and the communities around it, including Sunrise Manor, Las Vegas, Winchester, Whitney, and Moapa Town. Response times depend on where you are and how the day is running, but most repairs in and around North Las Vegas get handled same-day when the schedule allows. If you’re further out toward Boulder City or Moapa Town, call and we’ll give you a straight answer on timing. Our home page lays out everything we do. For close-by neighborhoods, see Gate Parts & Welding in Sunrise Manor and our Gate Parts & Welding in Las Vegas page. If it’s a structural repair rather than parts and welding, our Gate Repair in North Las Vegas service covers it.
Serving North Las Vegas, NV – Our Local Coverage Area
We serve North Las Vegas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Parts & Welding in North Las Vegas
It’s the repair of the structural metal and hardware that hold a gate together: hinges, posts, rails, rollers, latches, and custom welding done on site. Instead of replacing the whole gate, we fix the specific part that failed and weld it in your driveway. This is the work you call for when a gate sags, drags, wobbles, or won’t close.
Most single-part repairs take one to three hours on site, depending on what failed. A simple hinge or latch swap is quick. Post replacement or custom welding takes longer because the footing and alignment have to be reset. We give you a realistic time window when you book and stick to it.
Most repairs land between $150 and $650, with common hinge and latch work around the $200 to $400 range. The price depends on the gate’s size, the metal, and how much has to be replaced. We quote it upfront and in writing before any work starts. Call (844) 761-9351 for an exact quote. Estimates are free.
Yes. We service LiftMaster, Linear, FAAC, BFT, and Mighty Mule equipment, and we know where each one wears out on a typical North Las Vegas gate. When the mechanical parts and the operator need to work together, we check both. That way a parts repair doesn’t strain the motor afterward.
Often, yes. We offer same-day repairs across North Las Vegas when the schedule allows, and a live person answers the phone around the clock. Call (844) 761-9351 and we’ll tell you honestly what’s realistic for your gate. A gate that won’t close is a security gap, so we try to get it handled fast.
Every job carries the 90-Day Done Right Promise in writing. If the repair isn’t right, one call brings us back to make it right. It’s stated plainly, not buried in fine print or softened with “up to” language. That’s how the work should be.
Clear a little space around the gate and make sure we can reach it, especially the hinge post and the area where the gate swings. If the gate is powered, let us know when you book so we can plan for the operator and access control. If you have a written estimate from another company, have it out. The free second opinion costs nothing.
Schedule Your Gate Parts & Welding Service in North Las Vegas Today
If your gate is sagging, dragging, or failing at a weld, don’t wait for it to break all the way. Call Gatewood Fence & Gate North Las Vegas at (844) 761-9351 for a free, no-obligation estimate and upfront pricing you agree to before work starts. We answer around the clock, and the 90-Day Done Right Promise stands behind every repair.
Looking for more of what we do in North Las Vegas? Our Gate Installation in North Las Vegas service covers new builds, and Gate Motor & Opener in North Las Vegas covers powered systems. If your gate is part of an access-control setup, see Gate Access Control in North Las Vegas.
Written by the team at Gatewood Fence & Gate North Las Vegas.